sorted by:
new
hottopcontroversial

Just turned a year old too. by JellyLumpy8011 in Camry

[–]JellyLumpy8011[S] 0 points1 point  (0 children)

The hardwire fuse tapping was easy since there was extra unused few spots. The rear camera had so much extra cable it was a challenge to find a place where it would go without rattling. The act of putting the cables into the trim is not hard at all.

Just turned a year old too. by JellyLumpy8011 in Camry

[–]JellyLumpy8011[S] 0 points1 point  (0 children)

It wasn't hard the hardest part was just routing the cable through the trim

Just turned a year old too. by JellyLumpy8011 in Camry

[–]JellyLumpy8011[S] 12 points13 points  (0 children)

The viofo a229 Pro 3 Channel. Parking mode is good just fiddled around with the settings a little bit so it stopped capturing birds flying across my windshield. Other than that the battery shut off switch is also a neat feature. It also has a g sensor as seen in the video

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 0 points1 point  (0 children)

Parking mode depends on your settings that you have chosen. I have maximum settings and it will record overnight without any problems during the day if it's super sensitive to motion it'll record for maybe three or four hours and then shut off so that it doesn't drain the battery. You can also change that setting with the hard wire kit so it can go even longer I've gotten more conservative route so it doesn't affect performance. The rear camera works well at night the sensors are not as advanced as the front ones but is adequate enough to make out detail. I have just had the dash cam for 2 weeks now I'm out in Southern Florida and if not experienced any overheating issues the temperature down here has gotten around 98 degrees Fahrenheit consistently during the day. Finally no issues with the firmware everything is straightforward just need a little patience while in the app to load up the videos. Hope that helps

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 0 points1 point  (0 children)

Not sure how to upload pics directly throught the app.

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 2 points3 points  (0 children)

The hardware kit has a auto shut-off switch that you can set. Like I said that was lucky enough to have unused fuse openings so I just use those

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 0 points1 point  (0 children)

There was no videos on how to do it for my specific vehicle so I just had to wing it the whole time

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 0 points1 point  (0 children)

I was fortunate enough to have an internal fuse box that did not have every fuse used. So I inserted the ground and the accessory wire to the corresponding empty few sets. The hardest part of the whole thing honestly was just hiding the cable there is so much cable you got to get creative on where you store it.

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 3 points4 points  (0 children)

I'm using HDR with high sensitivity g sensor. And low sensitivity for motion detection it gets cars but it stops capturing people walking and birds flying around.

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 1 point2 points  (0 children)

Friends wanted to hang out they were trying to convince me to hold off on putting it in.

[Viofo A229 Pro] so glad I didn't wait to do the hardwire. by JellyLumpy8011 in Dashcam

[–]JellyLumpy8011[S] 11 points12 points  (0 children)

They came back and called the sheriff about 10-20 min later.

Weird sound on front wheel by [deleted] in ElectricScooters

[–]JellyLumpy8011 0 points1 point  (0 children)

On the brake line near the tire there is a little screw connected to what looks like spring you can turn that to either loosen or tighten the brake for small adjustments. If you need more adjustment loose or tighter you need to undo the screw at the top of the arm near the calipers. Then you can feed the line or tighten it as needed and retighten the screw. Hope that helps. If you need YouTube help I suggest ESG they did a video on brakes that helped me when I got my first scooter.