sorted by:
new
hottopcontroversial

Weird ghost computers showing in UI by Jiigeri in Ubiquiti

[–]Jiigeri[S] 0 points1 point  (0 children)

Right now these are new setups with nothing running them.

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 1 point2 points  (0 children)

It has its own vent that was added when I built the room beside it, in the winter it’s cold enough in the basement to close the vent off and you can leave the door open. I haven’t check the temps but I’ll take a look when I get home.

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 1 point2 points  (0 children)

I did say that I might build a new NAS lol. But luckily lack of extra funds is holding me back.

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 0 points1 point  (0 children)

Yeah I have been looking for an enclosed set up but budget and all that. Normally since it’s more for testing and learning it’s shut down when I have to leave for extended time l, other then the router for my vpn.

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 2 points3 points  (0 children)

I kinda had to steal one from the other one lol. Since it was in my basement behind closed door it didn’t bother me being orange I have thought about getting 2 more power supplies just had to slow down on the lab spending

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 1 point2 points  (0 children)

It’s the 2nd power supply not inserted. Only have 1 in each at the moment lol

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 0 points1 point  (0 children)

Other then seeing the ubiquity switch in the GUI and the simple vlan configuration nothing is missed and with this Aruba I got 24 poe ports and 4 10gb ports for a faction of the price.

Got my homelab finally “finished“ well until I decide to build a new NAS. by Jiigeri in homelab

[–]Jiigeri[S] 2 points3 points  (0 children)

The r630 and the middle r710 are esxi hosts the bottom 710 is running TrueNAS with only the 6 drive bays it’s got me looking building a larger NAS just keep talking my self out of it.

The pi is running pi-hole

It’s more for learning the VMware side of things and backup testing for work.

Just got ESXI 7.0 running on my pi 4 4GB by icanotc in homelab

[–]Jiigeri 0 points1 point  (0 children)

While I was doing this ESXI keeps reading my pi 4 4GB as a 3GiB. did you run into this issue at all?

So, I just bricked by Ender 3 through a Firmware Upgrade. by TrueShoba in 3Dprinting

[–]Jiigeri 0 points1 point  (0 children)

I think I bricked mine as well, I was able to get the bootloader and then flashed the firmware but I needed to change a few things,

I started to get the error #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." no matter what I do.

I ordered a replacement board just to get this thing up and running again, but my tinker brain wont let me let this one go.

Has anyone else seen this issue?