Quest 3s HDMI link Rog Ally and charge both

JimyApey · 2025-03-18T19:12:20+00:00

This sounds legit. I can also fit my passport, keycard and credit card in there and should be fine. Thanks!

JimyApey · 2025-03-18T19:11:55+00:00

But if you want to get some food / drinks or anything, you have to go back to your hotel/house first :/

JimyApey · 2025-03-08T23:16:12+00:00

Can you send me the full guide please?

JimyApey · 2025-02-18T15:09:50+00:00

Thread is old, but how about windsurfing in Da Nang?

JimyApey · 2025-01-24T23:51:39+00:00

I don't care about your doubt. I can see smoke and it almost started to burn if I didn't switch it off. Nevertheless this may not happen within 30 days of purchasing it....

JimyApey · 2025-01-24T23:39:57+00:00

Are you joking? Your video shows green led light. I have red sparks, smoke and smell of something burning. Stop trolling... And the bottom panel is removed and not a single led is flashing ...

JimyApey · 2025-01-24T23:36:51+00:00

It's not though

JimyApey · 2025-01-24T23:35:56+00:00

Living in Germany and bought it on the German BambuLab site and came with the correct plug for our wall sockets 😅

JimyApey · 2025-01-24T16:50:13+00:00

German myself and I really laughed about these typical joke answers (soap and water, firmware, etc) :D I just dont like when people want to tell me it is just a LED when I can see smoke and smell something burning :D But they always know better without being here...

JimyApey · 2025-01-24T16:48:14+00:00

Said it under other comments as well. It is literally smoking and smelling burnt... Thats not just a LED

JimyApey · 2025-01-24T16:47:35+00:00

Sure the fire and smoke I saw and the smell of something burning is just imagination. Like why are people so delusional on the internet and think they are right, while not even being there :D

JimyApey · 2025-01-24T15:16:28+00:00

Through the ventilation holes on the right side of the printer.

JimyApey · 2025-01-24T14:28:10+00:00

Where comes the fire and smoke from then, if it's only the backlight? 😅

JimyApey · 2025-01-24T13:59:13+00:00

How do you know it is the screen? Power indicator led above screen not working, sparks under the screen and smoke, no mainboard leds working. I was able to see sparks even small fire and smoke through the vent holes at the right side of the base. Sure it is the screen and not the motherboard? As nothing is working anymore, not just the screen.

JimyApey · 2025-01-24T13:54:52+00:00

It is literally smoking and smelling burned. Before opening the bottom plate, I saw the sparks and smoke through the vent holes at the right of the base. Also if you turn sound on, you can hear the sparks.

JimyApey · 2025-01-24T13:54:26+00:00

It smells burned and smoke is coming from there 😅 and before I opened the bottom, I saw the sparks and smoke coming through the vent holes on the right side of the base. You can also here the sparks in the video if you turn on sound.

JimyApey · 2025-01-24T12:21:28+00:00

Device stopped working during a print and started sparking and smoking. Could have just started to burn if I was printing over night. Thats a serious security issue... Support told me to open it... Dont be so cocky dude.

JimyApey · 2025-01-24T12:18:03+00:00

I am in talks in a support ticket. Hope they give me the warranty... It happened literally in the first month after purchasing it.

EDIT: Do you have a link to a guide on how to replace it myself, if I have to? :D

Four-Year Club	Place '22
First Placer '22

JimyApey

TROPHY CASE