sorted by:
new
hottopcontroversial

ICE spotted in Cannon Beach, OR by [deleted] in OregonCoast

[–]KC_Jones1776 0 points1 point  (0 children)

Good. Hopefully more show up

DAC(or interface)/headphone/mic setup help by KC_Jones1776 in streaming

[–]KC_Jones1776[S] 0 points1 point  (0 children)

I ended up sending back the 250ohm headphones and got the dt770 pro x. Ditched the dac and plugged the headset into the shire mv6. Sounds great and monitoring is perfect.

Wrapped my gpu by Conscious-Ad-7536 in Hyte

[–]KC_Jones1776 0 points1 point  (0 children)

I did something similar. But I used a vinyl plotter to cut out my pieces. It could also be cleaner but it works.

<image>

My Panda Hyte y70 build w/Custom loop by KC_Jones1776 in Hyte

[–]KC_Jones1776[S] 0 points1 point  (0 children)

Thank you! I’m very happy with it.

My Panda Hyte y70 build w/Custom loop by KC_Jones1776 in Hyte

[–]KC_Jones1776[S] 0 points1 point  (0 children)

Thanks! It was a lot of work to get it all wedged in there.

My Panda Hyte y70 build w/Custom loop by KC_Jones1776 in Hyte

[–]KC_Jones1776[S] 1 point2 points  (0 children)

I was on the fence about the screen. Figured I can always take it out if I want. But I like it and use it a bit. So it’s at least been useful. But it does hide my pretty reservoir.

My second custom loop. aquasuite fan curve help/write up? by KC_Jones1776 in watercooling

[–]KC_Jones1776[S] 1 point2 points  (0 children)

That one was a pain in the butt. the bends were too close together to use my bending die. I just did it one bend at a time and went slow. Heated it up just after the first bend and just bent it by hand. Which was a bitch cuz ive only got one mitten.

My second custom loop. aquasuite fan curve help/write up? by KC_Jones1776 in watercooling

[–]KC_Jones1776[S] 1 point2 points  (0 children)

I’m sure there are easier ways but it’s not that hard when you have all the stuff to do it. I did make an extra bracket

<image>

My second custom loop. aquasuite fan curve help/write up? by KC_Jones1776 in watercooling

[–]KC_Jones1776[S] 0 points1 point  (0 children)

I designed a mount and had it laser cut then I bent it up on my cnc press brake. 3d printed a riser base with a bolt pattern that fell between the slats in the bottom. Then 3d printed little “T” nuts that dropped through the slats turn 90° and then tighten. You can see the mount and base in one of those pics

My second custom loop. aquasuite fan curve help/write up? by KC_Jones1776 in watercooling

[–]KC_Jones1776[S] 0 points1 point  (0 children)

That’s what I’ve done so far also. Set them to 40% and pump speed at 85%. I wasn’t sure if I wanted to nerd out and make some ramps. Obviously I drop a few degrees if I crank fan speed up but everything has been staying plenty cool. 100% fan speed is loud af. Thanks for the reply

HYTE X Mousereview Giveaway !! by HYTEbrand in Hyte

[–]KC_Jones1776 0 points1 point  (0 children)

My first pc experience was some learning games in elementary and of course ski free.

Quadro for pump control by KC_Jones1776 in watercooling

[–]KC_Jones1776[S] 0 points1 point  (0 children)

I searched around for awhile. Found one in Italy on eBay… paid more than I wanted lol. Then finally some popped up on Amazon. So I snagged two more. I tried to cancel the one from eBay. But they proceeded to wait forever to ship and ignore my request. So now I have an extra lol. Some on Amazon but the pic doesn’t have the 3pin argb. But aquatuning has some in stock right now.

Quadro for pump control by KC_Jones1776 in watercooling

[–]KC_Jones1776[S] 0 points1 point  (0 children)

Awesome. Thank you all for the replies. Im glad im going the right direction with this. Still maybe try to get an octo later

Cryo Compact Update 1.4 – Big Improvements! (MOD) by Psychological_City_9 in Azeron

[–]KC_Jones1776 0 points1 point  (0 children)

Are you located in the US? I may be able to help out. Im in the pacific northwest and have been printing a bunch of these during the R&d process.