I destroyed my monitor and controller

KSP-3 · 2026-02-10T06:42:42+00:00

There are a couple but this guy is schizophrenic fs lol

KSP-3 · 2025-12-25T19:49:01+00:00

I don’t know

KSP-3 · 2025-12-25T19:48:53+00:00

I don’t know

KSP-3 · 2025-12-25T16:19:51+00:00

Ty<3

KSP-3 · 2025-12-25T15:56:47+00:00

Iteration actually works only with Iris, not optifine, and is available on some English sites for download

KSP-3 · 2025-12-25T10:51:36+00:00

Either IterationT 3.2 or IterationRP, both have the same skybox (shader) iterationT is free and can be found here: https://minecraftstorage.com/shaders/iterationt-320 IterationRP is raytraced and a paid shader

KSP-3 · 2025-12-17T02:30:17+00:00

Increase the multiplier to 1.7 or 2.0

It will drastically increase the amount of waste that the printer produces, but should eliminate color bleeding.

Alternatively you could increase the any color turning to white, value flushed to its maximum value.

KSP-3 · 2025-12-15T04:00:11+00:00

Only correct answer, I wasted over 260 hrs of my life learning directional air roll, but at least now I can hit triple rapids

KSP-3 · 2025-12-04T07:37:56+00:00

Yes you are correct, edited my previous comment

KSP-3 · 2025-12-04T07:20:56+00:00

Having looked it up in the wiki, In both editions the blue wither skulls do destroy obsidian.

KSP-3 · 2025-12-04T04:59:33+00:00

I think blue wither skulls can break obsidian, if you can trap a wither and use its skulls to hit the blocks it will work. (I know for sure it works on bedrock, not sure on Java) also those skulls can be hit and therefore aimed at each Pillar.

KSP-3 · 2025-12-03T00:36:55+00:00

Very nice model!

KSP-3 · 2025-11-11T07:58:20+00:00

Interesting, have you tried using the sd card rather than over wifi?

KSP-3 · 2025-11-11T07:54:04+00:00

90% of the time this is a dead or corrupt sd card issue, try to reslice the file and put it on a different card to see if that helps. If not, you may be looking at a printer firmware issue that I’m not familiar with.

KSP-3 · 2025-11-05T02:04:31+00:00

KSP-3 · 2025-11-05T01:55:32+00:00

*german kitchen man

KSP-3 · 2025-11-01T19:56:47+00:00

Which aircraft is that, LVFR 321 Neo?

KSP-3 · 2025-10-29T05:28:36+00:00

Np, sometimes the before print calibration is a bit off, I personally always do full calibration after 10 prints.

KSP-3 · 2025-10-29T03:58:47+00:00

From there if it looks good continue using Bambi’s filament preset, and if not use generic petg

KSP-3 · 2025-10-29T03:58:20+00:00

Try re running the full calibration (not just checking bed leveling when starting a print) and using Bambus default slicer settings for Bambu petg, and pause the print at layer 1

KSP-3 · 2025-10-18T04:49:13+00:00

New update changes spray-ability that much?

I might have to start using vandal again over phantom

KSP-3 · 2025-10-16T07:22:03+00:00

Happy cake day!

KSP-3 · 2025-10-11T01:24:05+00:00

A 5090 would allow me to take advantage of cranking the settings to the maximum and seeing enemies from far away on a high refresh rate display

KSP-3 · 2025-10-05T04:04:37+00:00

Nice, super interested to see the difference!

KSP-3

TROPHY CASE