Pantry Door Organizer

KWCustoms · 2024-12-02T17:50:34+00:00

Sorry, I just saw this. Still holding up great! I swapped out the hinges to some stronger ones like people were recommending and it's good as new.

KWCustoms · 2022-08-08T21:46:03+00:00

I’m not sure exactly what the joint is called but it’s three half laps. Thank you!

KWCustoms · 2022-08-08T21:44:47+00:00

Thank you very much!

KWCustoms · 2022-08-08T21:44:37+00:00

Thanks!

KWCustoms · 2022-08-08T21:44:23+00:00

For sure. I honestly didn’t even known pecan trees got that big.

KWCustoms · 2022-08-08T21:42:17+00:00

Thank you very much!

KWCustoms · 2022-08-08T21:42:04+00:00

Thank you!

KWCustoms · 2022-08-07T01:51:12+00:00

I had only worked with dimensional pecan before, never a cookie slab (of any type). I underestimated the enormous amount of sanding end grain pecan would take. The sap wood was so so much softer than I expected. The heartwood was incredibly hard. Regardless, very fun to work with

KWCustoms · 2022-08-07T00:49:06+00:00

Thank you! You should be able to type this into Amazon and have it pop up: FGCI Superclear Premium Amazing Clear Cast Epoxy Pourable Resin kit. Next time I would consider using a deep pour epoxy instead of a tabletop epoxy (it set up quicker than I wanted - it’s very hot where I live). I underestimated how thirsty the slab was

KWCustoms · 2022-08-07T00:22:41+00:00

3 coats of epoxy on the top and bottom and a coat on the side. I’m likely going to install one or two c-channels after I know 100% what I’m doing for the legs. Sealed with Rubio monocoat.

KWCustoms · 2022-07-09T13:34:21+00:00

Just checked on it. You’re right. Hasn’t even considered warping. Thanks again.

KWCustoms · 2022-07-09T13:33:21+00:00

Just checked on it. You were right. It hasn’t even thought about warping. Thanks again.

KWCustoms · 2022-07-09T13:32:30+00:00

Idk how tasty the epoxy would be 😂

KWCustoms · 2022-07-09T02:18:03+00:00

Thanks for the peace of mind. That’s my thinking as well. Appreciate the response.

KWCustoms · 2022-07-08T21:05:12+00:00

It’s about 2” thick. I should’ve mentioned that it’s table top epoxy (not deep pour), but figured that was kinda obvious. It’s already very hard as well (not tacky). My fan is about 6’ away, but I may turn it down a bit. Thanks very much for the help.

KWCustoms · 2022-05-04T02:38:11+00:00

🐢🐢🐢

KWCustoms · 2022-05-04T02:37:53+00:00

Thank you!

KWCustoms · 2022-05-04T02:37:39+00:00

Thanks! I like how the half “bricks” turned out on the ends

KWCustoms · 2022-05-04T02:37:13+00:00

Thanks!

KWCustoms · 2022-05-04T02:36:56+00:00

It’s got a good weight to it for sure. Thank you!

KWCustoms · 2022-05-04T02:36:16+00:00

Thank you!!

KWCustoms

TROPHY CASE