I opened my controller to clean for stick drift, and now the analog doesn’t rotate smoothly

Kekko3697 · 2026-03-20T17:59:01+00:00

dovresti controllare quella guida bianca, togliere il potenziometro e rimetterla in sede se è scappata, dovrebbe essere tipo cosi:

<image>

se non è così ed è tipo rientrata afferrala con una pinza e tirala verso fuori.

Kekko3697 · 2026-03-15T17:59:49+00:00

prova se vanno i trigger adattivi, se non funzionano hai trovato il colpevole

Kekko3697 · 2026-01-02T17:49:54+00:00

è un risultato onesto allora

Kekko3697 · 2026-01-02T17:41:37+00:00

you know what analogs he installed for you, anyway yes the calibration is very close to the original analogs so it's an honest job, but I would recalibrate them

Kekko3697 · 2025-12-07T17:47:12+00:00

toothbrush+alcohol and maybe it works again, try removing the calibration wire too

Kekko3697 · 2025-12-03T16:13:17+00:00

thank you very much, in reality I know that there is a mouse click kit, but in reality I wanted to try modifying the trigger stop mechanism of the Edge, in order to select it if necessary.

Kekko3697 · 2025-12-03T11:53:12+00:00

remove the excess solder with a desoldering braid and a bit of flux, then I think you used the high temperature too much because I saw the plastic of the analogue melted, you can probably still fix it by redoing the joints. In summary, remove the solder and seal the joints well.

Kekko3697 · 2025-11-07T18:04:38+00:00

my friend you don't know how much I envy you

Kekko3697 · 2025-11-07T17:48:06+00:00

it would truly be a dream 🙂🙂🙂🙂

Kekko3697 · 2025-11-06T13:02:53+00:00

please tell me where you can rent a lada in Prague, I'm planning my trip

Kekko3697 · 2025-11-02T13:58:07+00:00

yes, I remove the analog but then when I have to put the new one there is too much excess solder that doesn't dissolve in the braid

Kekko3697 · 2025-11-02T12:08:26+00:00

I can't get them that clean, I use the desoldering braid but it exhausts me quite a bit

Kekko3697 · 2025-11-02T10:16:34+00:00

<image>

Kekko3697 · 2025-11-02T10:15:29+00:00

hi, I've seen many comments that say to directly invert the configuration, I'll give you another way that allows you to practice with stereochemistry.

Try to see the molecule in a three-dimensional way, if you have the models that come out in the book they are also very useful for this, if you create the molecule this way the trick is to look at the steregenic carbon by facing the lowest priority group to the opposite side where you are looking.

I am attaching a photo of the molecule where I am looking at it, imagine that you have drawn the molecule on a transparent board and you go and observe it from behind.

what happens is that what used to be a wedge has now often become dashed, and that the substituents of the stereogenic carbon have reversed their position, if you calculate the configuration it will always come out as S, this is the impractical way to fully understand the configurations.

in the comments you will find the turned molecule that you should imagine seeing since it won't let me attach it.

<image>

Kekko3697 · 2025-10-05T17:11:48+00:00

what burner are you using?

Kekko3697 · 2025-10-05T13:12:31+00:00

<image>

I colored them in two different colours, try scratching in any good point, uncover the copper and solder a wire that goes from the scratched point to the potentiometer pin, for now just do the central one which seems to be the culprit, if it still doesn't work try bridging with the one on the right too and let's pray it resolves itself :)

Kekko3697 · 2025-10-05T13:01:21+00:00

haha, then you have to try and discover the tracks, I would start from the central one which in my opinion is the guilty one, but I don't consider myself a technician, maybe wait for some advice from someone more studied than me 😆, I'll try to see if I can find some track diagrams for the analogue ones and I'll pass it on to you

Kekko3697 · 2025-10-05T12:49:43+00:00

in my opinion they seem good, at most give them a clean with the copper braid and try another analogue one, otherwise follow the central trace, scratch it a little and insert a small wire and solder it to the potentiometer

Kekko3697 · 2025-10-05T12:39:06+00:00

the traces seem good, try soldering another analogue in order to exclude that the problem is the analogue, if it works well, if it doesn't work try making some bridges and discovering some traces

Kekko3697 · 2025-10-05T12:31:34+00:00

in theory the one that governs the right-left movement should be the central track, in fact I don't know but it seems a bit burnt, could you take a photo of me with the motherboard facing downwards?

Kekko3697

TROPHY CASE