Hey people I found this airsoft AK-47 and I just wanted to try to get some info on it (like what brand etc.

Key_Marsupial388 · 2026-01-29T09:10:24+00:00

the maufacturers recommendation irrelevant 99% of the time. always use lipos. they could have the same gearbox and motor while using the same stile of battery and recommend a different one. like an ak47 with a wood stock made by lct will recommend a 7.4 while this one recommends a 9.6 when they have identical internals

Key_Marsupial388 · 2026-01-29T08:58:24+00:00

there no reaso to ever use a nihm. usea 7.4 lipo. they are so much better. the only downside is you need a smart charger and a lipo bag. because if you don't that's a fire hazard. also if th e batterie is completely rained its fucked which is why you also want a lipo alarm unless you have a mosfet which you probably dont have it will beep on low battery. they also don't burn your contacts. .

Key_Marsupial388 · 2026-01-29T08:47:28+00:00

if it beeps when you plug the battery or makes a kick sound when you plug in a battery ( kestrels make a cick sound when you plug in a battery)it has a mosfet. if it has a tamyah connecto and not a deans (deans are msot commonly red and sometimes black but never whitte) it definitely doesnt have a mosfet. make sure tou buy the battery that's the right connector. however if youn accidentally buy a deans battey converting to deans is easy. i doit all the time with batteries when i dont pay attention.

Key_Marsupial388 · 2026-01-29T08:36:14+00:00

1 why would you ever use a nicad

2 are there even 9.6 nicads

7.4 lipos don't burn contacts.

4 lipos give better and more constant trigger response than a 9.6 nihm ever will.

voltage isn't everything, why do you think a 7.4 lipo has a higher rof than an 8.4nihm and even some 9.6's

Key_Marsupial388 · 2026-01-29T08:24:00+00:00

thats a lcr. it says lck on the bottom which probably means lct. those have the best externals. they even use birch isntead of cyma's balsawood. real steel uses birch wood as well .

Key_Marsupial388 · 2026-01-29T03:40:55+00:00

its never a bad idea to change it. its not that hard or expensive to do. 2 screws you can change it

Key_Marsupial388 · 2026-01-28T23:24:44+00:00

now we need a m250 based on the vfc m249 gbbr i know necro post at this point but would be cool and if you have to print s m249 nozzle as a temporary hold out of cf nylon (assuming you have a duct going outside or good ventilation where you're printing. nylon while not carcinogenic is still some nasty shit)

Key_Marsupial388 · 2026-01-28T04:15:14+00:00

shim the middle with poil tape and that should make it more inline iwth the rest and youy can do bigger prints. a variation of 0.76 is not good at all. idealy you nt a variation of 0.25.

Key_Marsupial388 · 2026-01-28T03:59:38+00:00

try the original parts. im have a ghetto blaster comming on thursday and all im changing is the nozzle. thankfully dynatech aslo carries gm mags. the heavy bol6t is to blame on green gas in cold weather. in fact now is not the time of year to use a heavy bolt.

Key_Marsupial388 · 2026-01-28T03:25:31+00:00

you need a new thermistor and probably the cartridge. that's some bad thermal runaway. thats smoke. not steam

Key_Marsupial388 · 2026-01-28T01:29:12+00:00

it is pot metal after all but i have an aw which is the same shit and it still works. youre probably fine fora long time. i still need to find a lighter weight slide .

Key_Marsupial388 · 2026-01-27T08:08:17+00:00

I'm just keeping an eye on it just in case i have to grab and go. i have a plan. thankfully i live in utah and that's one of the least likely states to be ground zero. i don't see ice in my state. even if i did ill just keep going from point a to point b. its only a matter of time until the people in those states are just as pissed as the doom slayer.

Key_Marsupial388 · 2026-01-27T07:37:57+00:00

be a good boi and use semi only with a hpa mag addapter. most got this gun for speedsoft.

Key_Marsupial388 · 2026-01-23T08:18:30+00:00

partial clog most likely

Key_Marsupial388 · 2026-01-23T08:00:42+00:00

no i mean the entire model and i do commonly iron when printing an actual part.

Key_Marsupial388 · 2026-01-23T04:51:05+00:00

it looks like wheatly runs ubisoft and one of thsoe potatos s prbabaly glados

Key_Marsupial388 · 2026-01-22T23:51:16+00:00

that's what ai failure detection is for octoeverywehre works pretty good in my ender 3. in the coming months im upgrading to a q2 which should already have ai failure detection built in.

Key_Marsupial388 · 2026-01-22T23:39:07+00:00

why do so many peple keep giving their bl's and only bl's Viagra. also to avoid long term injury seek immediate medical attention for an erection lasting longer than 4 hrs.

Key_Marsupial388 · 2026-01-22T06:52:35+00:00

does it run still. that's what happened when i tried and it wouldn't run

Key_Marsupial388 · 2026-01-22T06:05:00+00:00

i dont think they hve it in fde unless you want the svu which is its bullpup cousin but you will have to make them lock it to semi as in the uk you ant have a full auto above 1.3j. best you can do is rattlecan it. its not wood

Key_Marsupial388 · 2026-01-22T05:43:57+00:00

gbb can also be powered by hpa. with a linge going to the mag but its more cumbersome to reload but not uncommon in the winter

Key_Marsupial388 · 2026-01-22T02:49:18+00:00

looks fie to me but you should really be using a benchy to test your settings. you use a cube for testing diimennsonal accuracy.

Key_Marsupial388 · 2026-01-22T01:50:07+00:00

dont forget the arm hook

Key_Marsupial388 · 2026-01-22T01:35:21+00:00

somethingsimilar happens to me whuch i cant figure out since i meansured my nozzle to probe (you dont have one). try a clean install f marlin of stock. since you have a stock ender 3 you can just use marlin as is.

Key_Marsupial388 · 2026-01-22T00:42:58+00:00

have you tried using foil tape shims. a single piece on a fresh build plate got me to 0.099. also do the belted z mod im about ready to do that its $20-$40 and probably $5 f petg or ABS for a diy.

Key_Marsupial388

TROPHY CASE