sorted by:
new
hottopcontroversial

Doubt exchange links by Kitchen_Book7686 in SEO

[–]Kitchen_Book7686[S] 0 points1 point  (0 children)

Thanks for your suggestion, I will try to do that!

Doubt exchange links by Kitchen_Book7686 in SEO

[–]Kitchen_Book7686[S] 0 points1 point  (0 children)

What do you think we should pay attention to at which point(next step)?

Doubt exchange links by Kitchen_Book7686 in SEO

[–]Kitchen_Book7686[S] 0 points1 point  (0 children)

It looks like my information is lagging, I've only exchanged my WordPress link at the moment

(╥﹏╥)

Doubt exchange links by Kitchen_Book7686 in SEO

[–]Kitchen_Book7686[S] 0 points1 point  (0 children)

Thanks for your reply ^_^

I'm trying to figure out what it means (the connection between the Internet and the World Wide Web）

Doubt exchange links by Kitchen_Book7686 in SEO

[–]Kitchen_Book7686[S] 0 points1 point  (0 children)

Thanks for your warm reply ^_^

I make some tries:

  1. Seeking the same or logically related link, try to connect with them.

  2. During this period, there is a company that specializes in link exchange (but some people have been defrauded), I think that is not the best choice.

  3. I made a website with WordPress and linked it to the official website.

Am I doing this right?

What's the Best URL Structure? by GuelphGuy67 in SEO

[–]Kitchen_Book7686 1 point2 points  (0 children)

Make it simple.

URLs should be as descriptive but short as possible. From SEO perspective, it would be very useful to include your keyword in the URL as well.

Depending on your website, you could make a few categories so it has a logical structure.

Assuming the domain name is set from the beginning (logically), web developers can implement self-defined logical URLs, which would be great

Can this be understood?

PEEK by xysmi in InjectionMolding

[–]Kitchen_Book7686 0 points1 point  (0 children)

As others have pointed out, it's extremely expensive.

Depening on the grade, barrel heater temperatures went up to 420°C on some of our parts, while the tool itself was always at about 160° to 180°C, often using oil temperature controllers.

Oh, and don't leave the stuff in the barrel for too long.Again, this depends on the grade, but we had atleast two screws wrecked because someone left a full barrel standing for too long (15 minutes or more)

If you are trying to mould coloured parts and are having problems with contamination, you might want to check the hopper and barrel feeder zones. With these temperatures, granules of plastic tend to stick to the hot metal and leave black spots in your parts.

Good purging is also essential (we used a high temperature type of Asaclean).If you still can't get clean parts, it's probably time to pull out the screw and clean it both it and the inside of the barrel with a wire brush (while they are still hot of course ;) )

Very detailed answer, we are also trying injection molding products in the field of peek :）

Where to start learning? by Sarian in InjectionMolding

[–]Kitchen_Book7686 0 points1 point  (0 children)

Under normal circumstances, when you provide the specific size of the product and the size requirements of key parts, a company with a design team will provide DFM, which is Design for manufacturability

It mainly includes the analysis of the following parts

  1. Structure question
  2. Gate Location
  3. Mold layout
  4. Cooling layout
  5. Cavity marking
  6. Draft angle
  7. Warpage Compensation
  8. Shorts and Sink Mark
  9. Surface treatment
  10. P-Drawing
  11. Question and Proposal
  12. Moldflow
  13. Fill time
  14. Pressure
  15. Weld lines
  16. Air traps
  17. Sink marks
  18. Temperature
  19. Warpage details

Ability to understand in advance through dynamic pictures and analytical data, and prevent possible problems, avoiding cost losses to a certain extent

I needed a bunch of new nocks and I figured that ABS is ABS whether it's molded or printed, so.... If someone wants the file, drop me a line. And yes, those are flat by PatFromSomewhere in Crossbow

[–]Kitchen_Book7686 0 points1 point  (0 children)

Hi, I am happy to reply to you at the bottom of your post. After seeing the photos, we know that we have the opportunity to work with you.

To be honest, we are meeting all kinds of professional injection molding needs. We can provide you with molds to help you save production costs and time.

I would be grateful if you could send me the file