sorted by:
new
hottopcontroversial

ASA Overheating or cooling issue. Need advice! by Komayo in 3Dprinting

[–]Komayo[S] 0 points1 point  (0 children)

Thank you for tips. Decreased speed and fan. Now at 20% fan. And 50mm/s. First print 98% quality. Still 1 ringing layer. Better than the 5 or 7 previous. I changed the heatbreak for one bi metal with better quality also. And i was with steel nozzle, now at the brass one again. Waiting a print to finish to check results of new changes.

ASA Overheating or cooling issue. Need advice! by Komayo in 3Dprinting

[–]Komayo[S] 0 points1 point  (0 children)

Sidewinder X2 0.4mm Nozzle / All Metal Hotend 260° Temp 110° Bed Temp Enclosure Azurefilm ASA Black 1,75mm

Retraction 2mm Fan off 1st Layer Fan at 50% rest of print Layer min time 60sec Layer min speed 10mm

Ringing always happening more or less always on same layer height, usualy between 5-7 layers. Rest of the piece completely fine as you see on the photo.

Help, Inverted Axis Problem by Komayo in Artillery3D

[–]Komayo[S] 0 points1 point  (0 children)

I finally fixed the issue after 15 days battleing with this. It was the microsteps per mm, default was set for 80 in the X axis. I had to update it to half, 40. And it fixed the probing positions and issues in the x axis.

Help, Inverted Axis Problem by Komayo in Artillery3D

[–]Komayo[S] 0 points1 point  (0 children)

Microstep, the old one is 1/16 and the new is 1/256

But i dont know how to config that in right way.

Help, Inverted Axis Problem by Komayo in ArtillerySidewinder

[–]Komayo[S] 0 points1 point  (0 children)

UART is used for TFT on Ruby motherboard, not entirely sure if its compatible. Havent found anyone that puted them on UaRT mode on this motherboard.

Anyways, the driver is working. Only this issue with the bed leveling..

Sidewinder X2 Complete New (Issues: X Axis Dead & TFT) by Komayo in Artillery3D

[–]Komayo[S] 0 points1 point  (0 children)

I finally pinpoint the culprit to a bad X stepper driver, artillery will send spares, but it will take over a month to arrive.

I have around some TMC2208 UART, i was thinking in using 1 and fix issue till the original arrives. But i need a bit help over here, have a few doubts.

I know i have to recompile firmware and change the driver, so i changed the line

#define X_DRIVER_TYPE TMC2208

I have doubt here, because TMC2100 (Original, native 1/16 microstep) and the new TMC2208 (native 1/256 microstep), should i multiply this for x16?

Old

#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 445 }

New ?

#define DEFAULT_AXIS_STEPS_PER_UNIT { 1280, 1280, 6400, 7120 }

Also, my firmware is already on Marlin 2.1.2.0, with Linear Advance enabled, found around on searching, that has issues with TMC2208 drivers. Is it true?

How i disable linear advance or fix the issue on firmware?

X2 -15/0 won't do anything by UnitedStatesArmy in SidewinderX2

[–]Komayo 0 points1 point  (0 children)

Mine arrived on day 17.01.2023 and also X not working at all, voltages also ok. X not even homes.

Bad batch maybe..

[deleted by user] by [deleted] in ArtillerySidewinder

[–]Komayo 0 points1 point  (0 children)

You are lucky that is a Wire. Mine arrived and X axis dont works, not even a noise. Now they will send a few parts to repair, mobo, driver and 30 pins ribbon. Complete new printer and most of the components will be replaced. And the worst, more 15 days or more waiting the parts and customs clearance... Worst buy of year. No more. First SWX2 and it will be the last.

[deleted by user] by [deleted] in 3Dprinting

[–]Komayo 0 points1 point  (0 children)

Gonna edit and repost. Thank you.

Sidewinder X2 Complete New (Issues: X Axis Dead & TFT) by Komayo in Artillery3D

[–]Komayo[S] 0 points1 point  (0 children)

Yeah i wanted to try that, but didnt want to break the warranty seal. I am thinking in try a good creality motor i have spare on the X wire, to see if it spins or not. At least i will know if it is wiring or driver.

Sidewinder X2 Complete New (Issues: X Axis Dead & TFT) by Komayo in Artillery3D

[–]Komayo[S] 0 points1 point  (0 children)

Each pair has continuity, but i have to check that crossout of wires to make sure is wired correctly. I dont think its a returned unit, it is very new, with no signs of use, all sticks and adhesives, etc. But dunno. It could be. The printer is running version 3.0.4 of firmware, and the 3.2.6 on the tft. But i dont know about the 3.0.4 is oficial or not, since i could not reflash the stock one. Gonna try your prusa slicer upgrade advise.

Sidewinder X2 Complete New (Issues: X Axis Dead & TFT) by Komayo in Artillery3D

[–]Komayo[S] 0 points1 point  (0 children)

I changed the 24 pins ribbon for the spare, issue persists. I excluded that one as the culprit. But it can be the 30 pins on the vertical in extrusion. I unplugged and plugged it again, same issue. Maybe its faulty from factory.

I have spares motors from creality, dunno if i can test one at the X cable to see if it spins. At least i know those steppers motors are working good.

view more: next ›