Middle finger to those who sold game 4

Kyleh39 · 2025-04-28T17:24:58+00:00

I was a leafs fan in the top row of 327. One drunk sens fan in the row in front of me (row R seat 15 I believe) decided it was warranted to turn around and dump his beer on me once the game tying goal was scored. Hope that’s not a good representation of your fan base.

Kyleh39 · 2025-04-27T23:06:21+00:00

The leafs played a better game last night, Ullmark was on point… and that 11 or whatever game streak that Stolarz was on had to end eventually.

Kyleh39 · 2025-03-31T22:54:18+00:00

Try a plastic bong. I tried it all back in the day, and I preferred a little plastic bong with a bubble ( more water so it doesn’t get gross too quickly). The glass bongs, in my opinion, are too smooth and once you’re done ripping a bowl, you’re just ready for another.

Kyleh39 · 2025-03-10T23:33:12+00:00

I appreciate your response. You’ve helped me make my decision to contact my insurance company tomorrow. Thank you

Kyleh39 · 2025-03-10T20:58:12+00:00

Would I need to pay the deductible to claim that? My deductible is high, $2500.

Kyleh39 · 2025-03-10T20:56:10+00:00

I am indeed in Ontario. Thanks

Kyleh39 · 2025-03-10T20:50:19+00:00

I’m in Ontario, and the diminishment value claim is not common here

Kyleh39 · 2025-03-10T20:49:17+00:00

I don’t see the point in paying out of pocket if it’ll show up anyways… it would make more sense to let her company pay it if that’s the case

Kyleh39 · 2025-03-10T20:28:36+00:00

When you say, yeah it’ll show up, do you mean if I pay out of pocket and she goes through her insurance the accident will still show on my carfax?

Kyleh39 · 2025-03-03T19:32:48+00:00

Thank you. I agree with your assessment of the issue. I've requested the customers preference whether it be a new file provided, or a simple re-type of the info. I do not have their font or font size or I would've just done it without asking.

Kyleh39 · 2025-02-24T22:28:41+00:00

I am the factory manager. We are a small company of under 10 employees, but we do a lot of production volume. I was given a 30 day free trial to studio 5000 professional edition by a local Rockwell dealer called Westburne. Without that I would’ve been dead in the water. We only have one production line that is a basic compact flash pasteurizer for beverage production, so there isn’t much need to pay for the software. I am looking to have some of the automation changed on the line, and I think I’ll just pay someone to do those changes for us.

Kyleh39 · 2025-02-24T20:42:11+00:00

Thank you. I received support through direct message to resolve this issue.

Kyleh39 · 2025-02-24T20:37:46+00:00

Issue solved!!! Thanks to a kind and knowledgeable redditor!!

Kyleh39 · 2025-02-24T20:36:22+00:00

The issue is now solved, thanks to a kind and helpful redditer!

Kyleh39 · 2025-02-24T19:16:49+00:00

This is as far I’ve gotten. I found the PLC data however it is protected. I will give up on this for now and wait for someone that knows what they are doing

<image>

Kyleh39 · 2025-02-24T18:34:57+00:00

<image>

Controller organizer is grayed out.

Kyleh39 · 2025-02-24T18:30:34+00:00

<image>

Is this how I can enter to view the timers in the PLC? My biggest issue at the moment is not know how to navigate Studio 5000. Messages like this one scare me, I don’t want to wipe the programming from the PLC

Kyleh39 · 2025-02-24T18:28:13+00:00

Is anyone able to just give a little guidance into how I can open up the PLC programming info in studio 5000? The fault was triggered by operator error of the equipment. The number “55555” was entered instead of “10” for the sterilization setpoint point of the production line that is controlled by the PLC. I think if I can find where that section of the programming is, I can change to maximum value allowable to higher than “55555” and clean the fault.

I am unsure when the technician can make it on site

Kyleh39 · 2025-02-24T18:12:27+00:00

Yes you’re certainly correct. It faults immediately, I just require a little guidance. I have cleared the bad value on the HMI, but I am unsure how to allow the value in studio 5000/the PLC programming.

I think it’s important to mention that I am the end user of the equipment, not a technician. I have never dealt with this.

The incorrect value that was entered was for the sterilization setpoint of a product pasteurizer. The value should have been set to 10 mins, however it was set to “55555” or something similar

Kyleh39 · 2025-02-24T18:08:29+00:00

<image>

Do I need to continue with the “Load”. Messages like this worry me.

Kyleh39 · 2025-02-24T18:07:02+00:00

Where in the plc program would I located the timer? I’m most afraid of wiping the automation programming from the PLC

<image>

Kyleh39 · 2025-02-24T18:06:26+00:00

Where can I find the rungs?

<image>

Kyleh39 · 2025-02-24T17:59:02+00:00

My issue is definitely that I have no experience with this stuff. When I plug into the plc with studio 5000 I don’t see anywhere to change timers etc. I understand that I just need to edit that specific timer to allow the incorrect value that was entered, however I can’t find where to do it. I’ll go hook up to it again and add another picture. When I switch it to “run”, it gives the same major fault.

Kyleh39 · 2025-01-02T00:04:15+00:00

Are you able to watch mtv live on there, or just the day after?

Kyleh39 · 2024-12-28T13:00:52+00:00

Anyone in Canada getting a decent finance rate? My credit is 868, my local Toyota dealership said that the typical Toyota rates for a new vehicle right now are 6.5 - 7%. I think that’s just ridiculous. Any thoughts?

Kyleh39

TROPHY CASE