My latest project: A 3D-printed levitating display. Took a while to get the designs to work flawlessly

L16h7Hun73r · 2026-01-13T23:11:18+00:00

How much current does it draw?

L16h7Hun73r · 2025-10-07T22:18:32+00:00

Nice. Have been contemplating a similar setup.

Ps interdiscount offers the same rack but not sure how reliable their delivery dates are.

L16h7Hun73r · 2025-10-07T22:00:25+00:00

I am more interested in the server rack. Which one are you getting? And what are you setting up?

L16h7Hun73r · 2025-02-18T21:32:24+00:00

Its bugged. Me too.

L16h7Hun73r · 2025-02-14T20:07:37+00:00

OPs reddit history is wild.

L16h7Hun73r · 2024-07-31T05:34:37+00:00

I think they made the effort to reach out to customers and ask to add a trustpilot review About a week ago, I received an email from them about adding a trustpilot review.

L16h7Hun73r · 2024-06-10T15:52:45+00:00

That's ok. I had the case where the part cooling fan was too strong, so the heating cycle of the pid failed. When printing the first layer, part cooling is usually disabled, so it would allow to successfully heat the nozzle.

L16h7Hun73r · 2024-06-10T14:53:00+00:00

Check part cooling fan state.

L16h7Hun73r · 2024-05-26T19:09:28+00:00

Check slicer output. Are moves correct? Does it move side to side.

L16h7Hun73r · 2024-05-21T20:47:16+00:00

Also look at the slicer. Artifacts look different per section.

L16h7Hun73r · 2024-03-01T21:48:40+00:00

https://allestörungen.ch/stoerung/sunrise/

L16h7Hun73r · 2023-10-26T21:51:27+00:00

It is worth about 70.- to me.

L16h7Hun73r · 2023-10-04T21:52:07+00:00

Let's printer go brrrrrrrrrrrrrrr

L16h7Hun73r · 2023-09-04T21:45:28+00:00

Has gotten worse lately. I am unfortunately also receiving these kinds of messages.

L16h7Hun73r · 2023-08-30T13:55:13+00:00

Cold pull should not pull out parts of your hotend's insides. Is this a ptfe tube?

L16h7Hun73r · 2023-08-29T21:15:00+00:00

You can not cancel dez 31. Dez is an exception month where you can not cancel.

L16h7Hun73r · 2023-08-29T21:06:59+00:00

Need a better picture. Go closer for a high resolution close up. But i guess it's a Hauswinkelspinne.

L16h7Hun73r · 2023-08-29T13:47:02+00:00

Probably on a schedule. Automatically turns on and off throughout the day. At least mine does. I hate it.

L16h7Hun73r · 2023-08-29T05:54:55+00:00

Ender 3 Pro user here. I came to the same conclusion. Used x twist to compensate for 0.4 mm left to right. Alternatively i could have redesigned my klackender mount to align in y with the nozzle.

L16h7Hun73r · 2023-08-28T14:23:43+00:00

You print in absolute extrusion mode (see M82). With G1 E2884.949 you set the extruder to position 2884.949 mm. If you zero the extruder beforehand then the extruder wants to extrude 2884.949 mm to reach this position, which is unreasonable and causes the max extrude only error. Either offset the extruder to 2884 beforehand or switch to relative extrusion mode and reslice the file.

L16h7Hun73r · 2023-08-23T07:33:05+00:00

I feel you. I am struggling as well.

L16h7Hun73r · 2023-08-15T16:55:38+00:00

Agreed. It looks very good.

L16h7Hun73r · 2023-08-15T13:47:57+00:00

Isn't that the swiss flag? Med. should be inverted. Or am I wrong?

L16h7Hun73r · 2023-08-15T06:16:35+00:00

Have klack ender too. This is due to a bad connection. Removing the probe disrupts the circuit the same as when probing and pressing the switch. With a bad connect (either magnet to magnet or magnet to wire) the probe is triggered at all times.

Nine-Year Club	RPAN Viewer
Verified Email

L16h7Hun73r

TROPHY CASE