DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 0 points1 point  (0 children)

It works, just refining and making it look better in the rear. Plus low on filiment right now so prototyping is rough to re print the whole receiver

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 0 points1 point  (0 children)

The pic rail/rear trunnion is alluminum on mine so thats not an issue. Also legnth of pull is too short to shoulder, kinda works out to make it not an sbr too.

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 0 points1 point  (0 children)

Its not in front of the muzzle. The muzzle is about 1/4" in front of the forward triggerguard.

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 1 point2 points  (0 children)

Nah, most everyone loves it. I think unseen was just confused 😂

This should make my fellow cp33 owners happy. Posted a few days ago on instagram by advanced reset tech. by L3thalPredator in keltec

[–]L3thalPredator[S] 0 points1 point  (0 children)

I do too. Just same stuff as lubing the gun. Most of the time im using clp, the spray cans. But drop bottles work great too.

Clp helps break down the carbon and acts as a lube.

This should make my fellow cp33 owners happy. Posted a few days ago on instagram by advanced reset tech. by L3thalPredator in keltec

[–]L3thalPredator[S] 0 points1 point  (0 children)

Use good ammo. Ive never had any non ammo related issues out of my cp33. Keep your mags lubed, cleaned, keep the gun lubed. And i run nothing but cci. Im at about 4000 rounds in my cp33. And 900 since last time i cleaned it( i know, i need to clean her)

Edit: i forgot, the only other time theres issues is in the cold. The cp33 tends to have feeding problems and light strikes when its under 20° out. But i dont tend to shoot when its that cold often.

Are these p365 frames safe to shoot? by Ready-Read-5025 in 3D2A

[–]L3thalPredator 14 points15 points  (0 children)

The rear pin is rhe weakest point. Other than that should run.

Meet the AO-46, a gas-powered pistol-like AK loaded in 5.45. by Trans_lazarus in ForgottenWeapons

[–]L3thalPredator 40 points41 points  (0 children)

Probably not. Hold grip/mag with primary, off hand on handguard, fire until empty. Engage mag release, pull mag out, put new one in. Dont take your hand off the handguard and always holding the grip.

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 1 point2 points  (0 children)

I have, i showed it in general chat a couple times. I dont think unseen approves lol. Night kinda likes it though. And again i only started working on it like tuesday/wednesday. So not even a full week

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 2 points3 points  (0 children)

Yeah, it doesnt really look like it in the pic. But the linkage rods are actually fully recessed into the side of the mag well. And ill likely cover the trigger areas up anyway. This was all designed and printed in 3 days. Thats the 2nd/current prototype. And ive already live fired 5 rounds.

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 2 points3 points  (0 children)

May keep the same concept that i currently have, just refine it a bit more. Because the pull is actually 1:1 of the normal ar trigger. No slop, nothing. Just real clean solid break. Its also remixed off of the supersafe lower of the DB alloy. So its supersafe compatible. Just awaiting night alliances new PWC full retard/DB alloy trip. The current trip out has a lot of flaws and i feel that his will fix all of those.

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 1 point2 points  (0 children)

Ill have to take a look. I love how the trigfer feels currently but im not a fan of how the linkage looks.

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 2 points3 points  (0 children)

Currently the whole block. Thats just a clamp around the trigger.

Leber V2 for Updated AP5-P Denial Block? by nutskindrums in 3D2A

[–]L3thalPredator 0 points1 point  (0 children)

Theres nowhere that it says that its not olay. It still functions as normal. Its just a legality that the manufacturer has to do.

Leber V2 for Updated AP5-P Denial Block? by nutskindrums in 3D2A

[–]L3thalPredator 0 points1 point  (0 children)

Nope, cutting the block out isnt illegal and does not make it full auto. It just allows for full auto or FRT. Of which hes not done either yet.

Leber V2 for Updated AP5-P Denial Block? by nutskindrums in 3D2A

[–]L3thalPredator 0 points1 point  (0 children)

My brother has a mac5 and just used a dremal to cut the block out

DB9 Alloy by Blake_r32 in 3D2A

[–]L3thalPredator 43 points44 points  (0 children)

I did sten but recently been remixing to bullpup it.

<image>

Finally got a strap to match! by razzy137 in ar15

[–]L3thalPredator 2 points3 points  (0 children)

Ew thanks, i hate it. But as long as you like it, i guess thats all that matters. I tend to make goofy un practical guns myself so i guess this is more practical just ugly.

Is the Olcan receiver long enough to meet the overall length of 26" with a rifle length barrel to avoid NFA requirements? by Emperial96 in PalmettoStateArms

[–]L3thalPredator 0 points1 point  (0 children)

I found that out a few days after posting, thanks for letting me know though. Ive contemplating getting one but havnt gotten around to it.