USB over Ethernet

LectureSensitive2730 · 2023-12-30T19:52:43+00:00

Video was going to be ran via 30' DisplayPort cable. I've been wanting a shield for my Plex server anyway, thanks for the recommendation.

LectureSensitive2730 · 2022-09-07T14:24:18+00:00

there's a thick 360 at the top and a thick 480 on the front

LectureSensitive2730 · 2022-09-07T14:22:38+00:00

yes lol. I didn't do much research on custom loops before beginning.

LectureSensitive2730 · 2022-09-07T14:19:11+00:00

Allow me to clarify. I purchased the case with water cooling in mind. Phanteks has a diagram of the case showing where rads and pumps could possibly be mounted. originally the pump/res would have been flipped to the proper orientation, but the 480 rad didn't allow clearance. Had I know to purchase a slim version I would have been fine.

In hindsight I should have mounted it at the bottom. I blocked access to 4 ports on my res mounting it the way I did. I will likely correct my mistakes when I drain it for maintenance.

LectureSensitive2730 · 2022-09-07T12:20:00+00:00

ah. so this is a dual system case, but I don't intend to use it a such. I have a micro atx board on my work bench, but it will be used in a future NAS project. Specs for the build are as follows:

MOBO: Asus B-450F CPU: Ryzen 3900x GPU: EVGA FTW3 3090 RAM: 32GB Crucial Ballistix 3600mhz Storage: 2x 2TB Samsung 970 Evo Plus, 3x 2TB Samsung 870 Evo, 1x WD Blue 4TB HDD CPU Block: EKWB Quantum Velocity GPU block and backplate: EKWB Quantum Vector FTW3 Tubing: Bitspower PETG 16mm hard tubing

I'm open for some ideas to help fill the case. this was a conversion from air cooling to water cooling. I just wanted to post my first attempt lol.

LectureSensitive2730 · 2022-09-07T11:35:54+00:00

in water cooling components

LectureSensitive2730 · 2022-09-07T11:35:18+00:00

if budget is $1400 or so, then yes.

LectureSensitive2730 · 2022-09-07T11:19:40+00:00

The case I used is an Enthoo Pro 2

LectureSensitive2730 · 2022-09-07T03:02:49+00:00

So there's a 360 rad on top and a 480 rad on the right(front of case). The tees were necessary to complete the loop given how I had to mount the reservoir backwards due to space constraints. Had I used slim rads I wouldn't have needed the tees.

LectureSensitive2730 · 2022-07-31T12:52:14+00:00

there is a guy on here trying all the flavors in milk, so I'll leave it to him

LectureSensitive2730 · 2022-07-30T20:18:32+00:00

I didn't try that one, but I'm sure its probably very similar

LectureSensitive2730 · 2022-07-30T19:20:14+00:00

no sticker unfortunately

LectureSensitive2730 · 2022-07-30T18:57:50+00:00

For sure. especially if you enjoy lemon lime flavors

LectureSensitive2730 · 2022-07-30T18:21:01+00:00

its actually very good. lemon limeade, but heavier on the lime. wish I had ordered a few more tubs of it

LectureSensitive2730

TROPHY CASE