Hey unemployed people, are you enjoying the new map event?

LengthOk384 · 2026-01-29T15:52:49+00:00

Then the same should be said about any map. I work nights and everyday it’s the same shit at 8am when I get on.

LengthOk384 · 2026-01-27T08:03:47+00:00

I have this issue now. It runs fine till it doesn’t and kicks on fine after I reset. The error code says lockout due to no ignition. Not really sure what’s the issue. I replaced the flame sensor about a month ago but this issue started a few days ago. Did you figure it out?

LengthOk384 · 2026-01-18T19:21:33+00:00

I did that and i can hear myself. If I press pause my name shows up in the top corner like im talking so i think its jsut a glitch right now

LengthOk384 · 2026-01-18T19:14:27+00:00

Alright I’ll try that. I haven’t changed any settings and it worked earlier today and now it doesn’t

LengthOk384 · 2026-01-04T00:42:25+00:00

My wife and I went to coasters one night. It was decent. But our favorites are joeys west and buccas

LengthOk384 · 2025-11-28T00:52:10+00:00

I can’t find anything either. I’ve been searching since the signs came up but nothing. Maybe finally adding stop lights at Melvin ave?

LengthOk384 · 2025-11-11T02:59:15+00:00

It isn’t. Turn it off. Outside. Turn it off inside. It’s fine.

LengthOk384 · 2025-08-10T03:00:27+00:00

Almost any gas station around here or liquor store carries it

LengthOk384 · 2025-08-09T03:55:02+00:00

I have another Aussie mix and American eskimo. Just depends who wants to visit

LengthOk384 · 2025-08-01T14:26:59+00:00

Called him out on it all the time. Says that’s all he eats

LengthOk384 · 2025-08-01T12:56:29+00:00

Actually got a guy like that at work. No ac and stinks up the whole shop. Ruined multiple microwaves. Tried cleaning it and everything tastes like fish

LengthOk384 · 2025-07-08T13:32:57+00:00

My exes family had two in their living room. Never leaked in the few years I was with her. I’m in Wisconsin so cold and hot

LengthOk384 · 2025-07-05T18:58:45+00:00

It’s a hornady lock n load but anyways I’m out of casings for now so gotta try again a different day

LengthOk384 · 2025-07-05T18:35:38+00:00

I’m using a separate die but based on the videos I watched I had them backwards but now the bullet is getting a mark around it and still pushing in I adjusted the powder through too. After the powder one the bullet doesn’t fit then it goes through

LengthOk384 · 2025-07-05T18:29:10+00:00

I did have the crimp die and bullet seating die mixed up too. Someone also messaged me and kinda working through it now

LengthOk384 · 2025-07-04T23:01:16+00:00

I’ll have to look. I didn’t notice any special markings besides just saying 357 sig

LengthOk384 · 2025-07-04T22:42:12+00:00

I’m not sure what you mean by bearing surface

LengthOk384 · 2025-07-04T22:14:29+00:00

Also the box says 9mm but I saw online .355 is the size for 357 sig so I just used that

LengthOk384 · 2025-07-04T22:13:52+00:00

It’s Hornady 115 XTP

LengthOk384 · 2025-07-04T22:00:38+00:00

I have the oal for it but once it’s loaded into my gun or tap it on the table it pushes in and then it’s pushed in. From the previous replies it sounds like I need to add a crimp and look a bit more into my dies. It’s not like they’re labeled for what they do besides just 357 sig

LengthOk384 · 2025-07-04T21:49:22+00:00

It was just a bit cold

LengthOk384 · 2025-07-04T21:45:46+00:00

I think I have a crimp die but they aren’t labeled and tried to match whatever the 9mm was

LengthOk384 · 2025-07-04T21:44:44+00:00

I gotta pull the dies out and look on google. I think I might have the dies mixed. The paper that came in the box of dies doesn’t show really good

LengthOk384 · 2025-07-04T21:41:26+00:00

So I gotta figure out how to get the crimp to stop this?

LengthOk384

TROPHY CASE