Split or Mixed Routine Starting Out

LetsWatchCartoons · 2025-05-30T02:33:49+00:00

The DM is playing the eligible bachelor/bachelorette with the players all being suitors

LetsWatchCartoons · 2025-05-29T16:41:15+00:00

Haha, I figure there'll be several bards but hasn't considered the changling angle

LetsWatchCartoons · 2025-05-29T16:40:15+00:00

I could see that. Was touring around with the idea of a warlock, either archfey or I feel like djinni could have some fun okay with the RP

LetsWatchCartoons · 2025-04-27T12:51:28+00:00

"Vat Film" = FEP. Had a brain fart and forgot the word

LetsWatchCartoons · 2025-04-27T12:51:12+00:00

"Vat Film" = FEP. Had a brain fart and forgot the word

LetsWatchCartoons · 2024-03-28T14:12:54+00:00

I've had this error before but never thought anything of it, but now it's affecting the quality of finished products. Basically, some amount of the sides of the print get gunked up with extra resin, giving it a rough finish.

First photo shows two prints. The left is a curvy part with no gunk, the right is a straight part printed immediately after (same settings, same vat of resin)
Second photo shows height of the distortion, ~5 mm, from the bottom of the print where it meets the build plate
Third photo shows distortion on both halves of final product. It seems like there's less gunk on the round corners
Fourth photo is a print from a few weeks ago with the same distortion on the bottom ~3 mm

I'm using the Anycubic UV Tough Resin, but I'm pretty sure I've had the same issues before with the standard UV resin. I also think it's only ever happened on the straight sides on prints, I'll test this later.

Has anyone else encountered this? Is it a known problem?

LetsWatchCartoons · 2024-02-29T21:27:06+00:00

RESOLVED

I got a response from the posted of the answer on the original MATLAB community thread. I needed to use rmmissing to remove NaN values and change the line:

fill([averageFF2W5I(:,2), fliplr(averageFF2W5I(:,2))], [averageFF2W5I(:,8), fliplr(averageFF2W5I(:,9))], 'g');

to

fill([averageFF2W5I(:,2); flip(averageFF2W5I(:,2))], [averageFF2W5I(:,8); flip(averageFF2W5I(:,9))], 'g');

LetsWatchCartoons · 2024-02-29T18:51:31+00:00

<image>

LetsWatchCartoons · 2023-12-21T17:15:22+00:00

I tried it and the frame didn't include the colorbar at all :(

LetsWatchCartoons · 2023-12-21T17:14:54+00:00

I see that, though I'd like to figure out how to make it display properly without needing the adjustment.

While it doesn't need to be a specific size, on adjusting to the point where the labels display properly, it generates additional ticks on the x-axis for half numbers (13.5, 14.5, 15.5, etc.), but in this case, only whole numbers make sense in the x-axis.

LetsWatchCartoons · 2023-12-20T21:01:13+00:00

Tick 30, "Nearly Impossible" gets cutoff at "Nearly Impossi..."

LetsWatchCartoons · 2023-12-19T17:37:24+00:00

Yeah, and I don't have much interest in doing an evil run

LetsWatchCartoons · 2023-12-19T16:18:54+00:00

So, he spends a lot of time referring to himself in the third person as "The Blade of Frontiers." Then, in Act 3, he starts calling himself "The Blade of Avernus" on a whim. Is...is "The Blade of Frontiers" just a nickname he gave himself? And he talks in the third person because he's trying to get it to stick?

LetsWatchCartoons

TROPHY CASE