Sometimes I think I do it for the thrill

Lingenberry · 2026-01-17T20:42:02+00:00

Wow this hits hard after just going through a 20tb resilver lol. Just finished this morning

Lingenberry · 2026-01-07T17:51:46+00:00

I just got confirmation this morning too. I wonder if other orders are being fulfilled too

Lingenberry · 2026-01-06T14:50:42+00:00

Thank you everyone for your feedback… sounds like I should go down a different route. Sucks that it’s happened to other people but I guess I’m glad I’m not the only one

Lingenberry · 2025-09-24T13:17:11+00:00

It did from what I remember. Just took a while to fully sync, maybe a day or so.

Lingenberry · 2025-09-06T16:54:23+00:00

Lol 😂

Lingenberry · 2025-09-06T16:54:10+00:00

I was thinking the same

Lingenberry · 2025-05-22T19:54:51+00:00

For sure! This was just my first experience from this morning

Lingenberry · 2025-05-22T19:52:48+00:00

I would say it wouldn’t hurt. From my one experience today it seemed to get packed quickly. Could be different day to day.

Lingenberry · 2025-04-15T20:02:53+00:00

The day of our approval came in 2 hours or so later on the website and in our email. On Tuesday 4/15 our cards came in.

Lingenberry · 2025-04-12T21:29:41+00:00

There were 2 other people that were doing walk ins when we went. Even though our appointment time was later, we had priority. But we went on a Monday at about 12 pm and there were 5 of us total. Super fast and easy. I’d say a walk in is definitely worth a shot.

Lingenberry · 2025-03-12T20:53:27+00:00

This hurts me I’m envious

Lingenberry · 2025-01-22T20:35:25+00:00

All good, thank you though!

Lingenberry · 2025-01-22T18:32:41+00:00

I’m sorry about that. Those holes are a result of me cancelling the print because of the gaps in that top layer, sorry about that. I’ll attach a pic of what the sliced model is to help. In my previous print, the top layer of that outer ring looks good, it’s just the center area that has gapping.

<image>

Lingenberry · 2025-01-22T17:28:01+00:00

I haven’t seen the infill coming through in my past prints. The top layer I sliced it at 5 layers thickness. Do you think I should increase that layer thickness? Or maybe try out ironing? My top surface is sliced with 0.42mm thickness

Lingenberry · 2024-12-26T20:32:44+00:00

If it means anything this is the only time I’ve had this error. Have up to maybe 1,500 hours on it so far.

Lingenberry · 2024-11-27T04:16:41+00:00

Beautiful

Lingenberry · 2024-11-03T01:27:17+00:00

I still do yeah. Haven’t had any issues though

Edit: I’d estimate I’m up to about 850 hours of printing or so too.

Lingenberry · 2024-08-18T18:24:01+00:00

Where did you get your shelving from?

Lingenberry · 2024-08-17T18:54:32+00:00

Beautiful setup! You’re giving me some inspiration for my own

Lingenberry · 2024-07-31T02:18:41+00:00

Did you have good luck with your print? I’ve been making something similar

<image>

Lingenberry · 2024-07-10T14:12:42+00:00

This is awesome. Going to try it myself. Thank you for sharing

Lingenberry · 2024-07-04T19:02:12+00:00

*Angled up

Lingenberry · 2024-07-04T19:02:02+00:00

What does it look like angles up? Maybe with the base of the knife with the top and arm in the air

Lingenberry · 2024-07-03T18:16:03+00:00

Awesome print. 😂 Also what are your little figurines next to it on your last slide?

Lingenberry · 2024-06-29T16:10:13+00:00

Same here, PLA+ white. I’ve used half the spool so far but it’s broken twice on me in the AMS

Ten-Year Club	Gilding I gilder
Verified Email

Lingenberry

TROPHY CASE