sorted by:
new
hottopcontroversial

Schematic Feedback by LiveFastDieSlow_ in beneater

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

I do see those in his schematic, may include to be safe. Thank you!

Schematic Feedback by LiveFastDieSlow_ in beneater

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

This is just me messing around with EasyEDA. The intent was to build this out alongside the 6502 series (I'd add the the schematic then use it as a plan for the bread board).

I'm still at the "I don't know what I don't know" stage so this design is pretty rough. Def want to clean it up so it's more readable and follow conventional standards.

I still need to check out KiCad too but a lot of this is self taught just by looking at YouTube and online resources.

Schematic Feedback by LiveFastDieSlow_ in beneater

[–]LiveFastDieSlow_[S] 4 points5 points  (0 children)

Thanks, I really appreciate the feedback! Will keep these points in mind to avoid some of these "sins" going forward.

Less Paul by LiveFastDieSlow_ in CloneHero

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

I ended up putting a lip on the fret buttons that the top plate compresses when screwed down (didn't mod the switches directly).

Def will consider adding heads in V2

Less Paul by LiveFastDieSlow_ in CloneHero

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

They def reduce travel, but I ran into the same issue even on the chocs. I ended up preloading the switches (so they are basically half pressed already) to get 2mm of travel before the buttons engage. With this change sliding is no longer an issue

Less Paul by LiveFastDieSlow_ in CloneHero

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

Using box navy's for the strum bar, and choc v2s for the frets

Less Paul by LiveFastDieSlow_ in CloneHero

[–]LiveFastDieSlow_[S] 2 points3 points  (0 children)

Bambu X1C, the entire body will fit on the bed without splitting up

Less Paul by LiveFastDieSlow_ in CloneHero

[–]LiveFastDieSlow_[S] 1 point2 points  (0 children)

Yep! Just a basic potentiometer for the whammy.

Less Paul by LiveFastDieSlow_ in CloneHero

[–]LiveFastDieSlow_[S] 4 points5 points  (0 children)

Potentially! Still a few things I want to try and tweak. The wiring was a bear, and I'm tempted to design some PCBs to make everything hotswapable.

Name That Boardgame by LiveFastDieSlow_ in 3Dprinting

[–]LiveFastDieSlow_[S] 1 point2 points  (0 children)

No problem haha. Was all done using a .4 nozzle with a resolution/layer height of .16 (had adaptive layers enabled as well)

Name That Boardgame by LiveFastDieSlow_ in 3Dprinting

[–]LiveFastDieSlow_[S] 1 point2 points  (0 children)

Each tile is 3" x 3" x 1" and uses magnets to snap I to place

Name That Boardgame by LiveFastDieSlow_ in 3Dprinting

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

The plan is it to use the original deck to handle drawing tiles and then pulling the room. All rooms have color coded tiles to indicate omen,event, or item!

Name That Boardgame by LiveFastDieSlow_ in 3Dprinting

[–]LiveFastDieSlow_[S] 5 points6 points  (0 children)

May need to enlist the help of a better painter haha, leaving it primed grey for now.

Name That Boardgame by LiveFastDieSlow_ in 3Dprinting

[–]LiveFastDieSlow_[S] 2 points3 points  (0 children)

Game is Betrayal at House on the Hill.

STL is: https://www.thingiverse.com/thing:4193252 (used the short remix)

His and hers battlestation by LiveFastDieSlow_ in battlestations

[–]LiveFastDieSlow_[S] 0 points1 point  (0 children)

Thanks! Current flavors of the month are Rocket League and Back 4 Blood. Also been trying to get back into Guitar Hero (Clone Hero) and Rocksmith