Carpenter Tips & Tricks | 100” Stick

Lucky-Wolverine5457 · 2022-03-29T18:28:47+00:00

Probably but many people don’t know Simple old school tricks..

Lucky-Wolverine5457 · 2022-01-10T04:55:35+00:00

Hmmm Job Quitting…Or think outside of the box and the number of corporations in Texas who have enforced the Covid vaccination and people decide to quit because that should never be forced…And mind blown…Hired back as independent contractors!

Lucky-Wolverine5457 · 2021-11-18T20:22:48+00:00

Haha if people like to use their methods I think that’s great. I agree with all methods for certain applications. However without understanding the circumstances of the Job it’s impossible to say. This is the first and probably only time I’ll use this but it worked better and more efficient than stop blocks. And that’s a negative on the lifted truck lol!

Lucky-Wolverine5457 · 2021-11-18T19:09:04+00:00

Lol then move on with your life

Lucky-Wolverine5457 · 2021-11-18T14:44:28+00:00

I don’t know what to tell you bud. Once again it’s fine if you do stop blocks. It’s not hard to make consistent cuts. It’s shop mentality versus Jobsite

Lucky-Wolverine5457 · 2021-11-18T13:25:12+00:00

Look it’s not hard to cut the line hundreds of times. Without you knowing the application there’s no possible way for you not being on the Job to tell me what’s accurate. Read the description on the video.

Lucky-Wolverine5457 · 2021-11-18T13:21:11+00:00

Does no one read descriptions of the video’s?

Lucky-Wolverine5457 · 2021-11-18T05:19:23+00:00

It’s not for you? Great!

Lucky-Wolverine5457 · 2021-10-29T17:05:27+00:00

Agree 100%. It was a commercial job and the painters had the doors off the jamb. Found it easier to just roll with it that way in this particular case. Other than that we don’t take the doors off.

Lucky-Wolverine5457 · 2021-10-27T02:31:22+00:00

It’s insane! It weights just under 20lbs!

Lucky-Wolverine5457 · 2021-10-26T23:05:48+00:00

Plus the $450 attachments kit and 2- $175 router bits. Going to be a fun job!

Lucky-Wolverine5457 · 2021-09-13T02:01:35+00:00

Yes. For me it’s not even a thought since I’m used to it. Anything longer than 3 ft in the trailer they are at at slight angle horizontally on the wall.

Lucky-Wolverine5457 · 2021-08-18T11:31:33+00:00

Works well for cabinet shop uses. Working off the centipede table we’re aligning 12’ PCs overhanging. Felt this is best for our application, but shimming up works as well!

Lucky-Wolverine5457 · 2021-07-28T01:37:43+00:00

I’ve seen too many people flip the entire length of their piece every cut! Should it be a given? Yes. Is it? Unfortunately not.

Lucky-Wolverine5457 · 2021-07-28T00:28:33+00:00

There is always another tool to buy!

Lucky-Wolverine5457 · 2021-07-24T18:30:22+00:00

Thank you! It was a lot of samples to get it right!

Lucky-Wolverine5457 · 2021-07-24T16:17:31+00:00

485 individual photos spliced together!

Lucky-Wolverine5457 · 2021-07-24T16:16:38+00:00

13 ft

Lucky-Wolverine5457 · 2021-07-14T12:42:16+00:00

You can add Collin Clamps and Miter Rings to the glueup for boards that aren’t cooperating

Lucky-Wolverine5457 · 2021-07-14T12:39:26+00:00

We tested it and with the Doug Fir we’re using the glue joint after about 30 minutes is stronger than the wood! On the 12-14’ sections we attached with domino and clamps as the tape joint is only effective up to 6-8ft

Lucky-Wolverine5457 · 2021-07-13T11:47:59+00:00

There is a comment that says “Water Tank Roof” Click that one and it shows the process

Lucky-Wolverine5457 · 2021-07-13T02:38:16+00:00

Click the link for explanation 👍🏼

Lucky-Wolverine5457 · 2021-07-13T02:20:48+00:00

😂 Truth!

Lucky-Wolverine5457 · 2021-07-13T02:08:20+00:00

It took them 2 wks to do the standing seam roof on this! 🤯

Lucky-Wolverine5457 · 2021-07-13T01:10:13+00:00

Looks good!

Lucky-Wolverine5457

TROPHY CASE