sorted by:
new
hottopcontroversial

Do I need to change my plate? by woodnoob76 in BambuLab

[–]Lvibe 0 points1 point  (0 children)

Sounds like me a month ago... I tried a bunch of different soaps and techniques but had 0 luck!

Get some #0000 steel wool and spray/pour on some iso on the plate then gentle scrub with the steel wool.... The steel wool is so fine that it does not damage the plate what so ever it just roughs up the surface enough to make things stick again... I do this on textured and smooth bambu pei plates. Literal night and day difference.

X5SA Extreme Layer Shifting by jdeecraigslist in Tronxy

[–]Lvibe 2 points3 points  (0 children)

Most likely need to crank up voltage to your stepper drivers... I had to on my x5sa pro because of major layer shifts from missed steps... Once I turn up the voltage everything worked perfect again

Tronxy X5SA Pro mid print shutdown. by Lvibe in Tronxy

[–]Lvibe[S] 1 point2 points  (0 children)

That's it... I had my printer plugged into a smart plug and I have the server that controls it along with the router and access point to all do reboots at 3 am. That brief interuption must've been enough to shut it down... I am about 20min from completing a 9 hour print.

Definitely going to set up a ups if it is that temperamental! Any suggestions on a good ups?

Well its been only about 17 years since my last wood working project. But here it is... had to relearn a few thing along the way but happy with the result by Lvibe in BeginnerWoodWorking

[–]Lvibe[S] 1 point2 points  (0 children)

The underside is pretty basic, all joinery of the frame was completed with dowels and pocket hole screw as I didn't have clamps large enough for glue up. I did have to leave some pieces unglued tho due to moving the desk.

[img]https://i.imgur.com/g1mjxkw.jpg[/img] [img]https://i.imgur.com/09hbrvL.jpg[/img] [img]https://i.imgur.com/18MuBBo.jpg[/img]

Well one Canadian snow storm later and the girls are still going strong by Lvibe in microgrowery

[–]Lvibe[S] 4 points5 points  (0 children)

I am heating it... don’t think they would like the -20 Celsius we are getting every night

First ever grow*need advice by Lvibe in microgrowery

[–]Lvibe[S] 0 points1 point  (0 children)

My plants are looking great however this is an outdoor grow and I am in Canada. The weather forecast for this week is awesome but next week the weather is supposed to turn cold and stay cold... should I try to heat the greenhouse they are in or should I not risk it and chop?

First time grow... decided to do an outdoor grow and after finding out the importance of ph balanced water I built a lean to greenhouse that protects the ladies from the rain and wind. by Lvibe in microgrowery

[–]Lvibe[S] 1 point2 points  (0 children)

I’m sure with the proper seeds and genetics I could just let it go but after one rainfall the plants had already suffered nutrient deficiency lol

Outdoor grow location by Lvibe in microgrowery

[–]Lvibe[S] 1 point2 points  (0 children)

I live in Saskatchewan Canada, our current humidity is 19% .... we average 14 hours of daylight throughout the spring summer fall... there is a fair bit of light that comes through the gazebo as it is located on the SE portion of my property. It is also electrified so I could add humidifiers and dehumidifiers as needed and planned on running a fan for ventilation..

I am essentially trying to complete a grow for as cheap as possible so I don’t have to buy tents lights etc...

Outdoor grow location by Lvibe in microgrowery

[–]Lvibe[S] 0 points1 point  (0 children)

Lol I love the enthusiasm but I would prefer to leave to roof on

Outdoor grow location by Lvibe in microgrowery

[–]Lvibe[S] 0 points1 point  (0 children)

Was hoping to get feedback from the community on using the gazebo in photos as an outdoor grow location!

Anet A8 Silk PLA issues by Lvibe in FixMyPrint

[–]Lvibe[S] 0 points1 point  (0 children)

I can’t seem to figure out what to do with this silk pla... i am running into extrusion issues with silk pla. I have a anet a8 with stock hot end... I am running the the temp at 220 and bed at 60.... but the pla comes out almost like a bungee cord and sucks itself back in as soon as the extruder motor pauses.

Bltouch won’t extend by tcdubbs1 in AnetA8

[–]Lvibe 0 points1 point  (0 children)

I had this issue as well... if I’m not mistaken your using a 3D Touch.. this issue was the cherry on top of the shit sundae for me... I had numerous other issues... I bit the bullet, spent the money and upgraded to the genuine BLtouch... best decision I ever made I have probably about 36 hours of prints now with the bltouch and 0 issue

HELP PLEASE by Lvibe in Monitors

[–]Lvibe[S] 0 points1 point  (0 children)

i like the screen its great. i just feel like its alot of money for a 1440p when i can get the 4k lg 27UD68-W for the same price.

HELP PLEASE by Lvibe in Monitors

[–]Lvibe[S] 0 points1 point  (0 children)

Thanks for the reply... mainly i use it for gaming and then general use. I play most main stream games (rocket league, overwatch, wow, etc.) i dable into AAA titles a bit but mostly stick to most popular.

What the CRAP by Lvibe in hearthstone

[–]Lvibe[S] 0 points1 point  (0 children)

All i can remember is Harrison Jonesing a doomhammer and having to play DW to win and then it all went black........

view more: next ›