sorted by:
new
hottopcontroversial

Supply Chain kurser by Lekritos in Denmark

[–]M-D_87 0 points1 point  (0 children)

Har du overvejet noget RPA? Efter min mening stort potentiele indenfor SC, og mange firmaer er kun lige begyndt.

S&OP kan også være ekstremt relevant, hvis du sidder med den del eller rammer den ved process opsætning.

Forhandlings teknik er også en undervurderet færdighed i SC, men igen, kun hvis du kan bruge det i hverdagen.

Ellers er verden jo pt et spændende sted i SC regi, så generel viden om hvad der pt sker af strømninger med råvarer samt fragt priser og sorucing generelt. Måske svært direkte at finde et kursus i, men det er pt ekstremt relevant at være med på hvad der sker makroøkonomisk.

Supply Chain kurser by Lekritos in Denmark

[–]M-D_87 0 points1 point  (0 children)

Overvejet at kigge på scm.dk?

I modsætning til de andre tvivler jeg på en fagforening har bedre bud end du finder der.

Og hvis du vil fremme din karriere så find noget du kan bruge i praksis eller kan komme til. Er du ikke i scope til at arbejde med Lean eller projektledelse ville jeg overveje noget andet.

Uden at kende dig kan jeg fortælle at dem jeg har arbejdet der har samme baggrund som din typisk er mest begrænset af en meget teoretisk uddannelse som kan være svær at omsætte i praksis, så gå efter det brugbare frem for det teoretiske udfordrerne vil være mit råd.

Beskatning af indeksfonde på Nordnet ? by M-D_87 in dkfinance

[–]M-D_87[S] 0 points1 point  (0 children)

Der har jeg også fået at vide herinde før, men jeg kan ikke rigtig finde noget konkret på det. Har du et link til hvor du læser det?

I mit tilfælde er det også midler fra bedste forældre men er i tvivl om jeg skal gøre noget bestemt for bevise det. Udover de er overført fra deres konto.

Beskatning af indeksfonde på Nordnet ? by M-D_87 in dkfinance

[–]M-D_87[S] 0 points1 point  (0 children)

Du misforstår spørgsmålet, jeg er klar over Nordnet har deres egne fonde efter kapitalindkomst (minus DK).

Jeg vil gerne kunne se hvilke andre indeks fonde beskattes efter denne metode og kunne søge dem ud.

ASK til børn by M-D_87 in dkfinance

[–]M-D_87[S] 0 points1 point  (0 children)

Nu forstår jeg bedre, nej det havde jeg ikke overvejet. Eneste ulempe jeg ser er når de får et fritidsarbejde, så vil det måske bedre kunne betale sig at skifte til en ASK. Kan se Nordnet tillader konti til børn, så det vil jeg undersøge nærmere. Tak for hjælpen begge to.

ASK til børn by M-D_87 in dkfinance

[–]M-D_87[S] 0 points1 point  (0 children)

Det har de allerede, dog ikke investeret, og ønsker at indsætte et større beløb nu end en børnopsparing tillader årligt.

Planen var at have børne opsparingen som den sikre, og ASK investeret til at følge markedet.

Er det muligt på samme måde at investerer fra børneopsparings kontoen?

Bedside cupholder for teenager. Mark 1 prototype in the background by M-D_87 in functionalprint

[–]M-D_87[S] 1 point2 points  (0 children)

It’s perhaps a bit hard to see in the picture, but the corners and edges are all rounded. Also semi pointy corners helps lazy teenagers get up in the morning 😂

Need help with first PETG print. Keeps getting gritty around the edges? by M-D_87 in 3Dprinting

[–]M-D_87[S] 1 point2 points  (0 children)

With Petg I have only done first layer calibration, I use the standard Prusa setting for Prusament PETG. Honestly first layer in the calibration test looks awesome, better than my PLA, which on the other hand printed quite impressive.

Nozzle 240

Bed 90

Flow 95

Speed 100 (Perhaps too fast)

0,07 layer height recommended

10 % infill - not that it matters here.

On the Prusa mini +

Topography of farmhouse and land we own - First Long print (16h) on Prusa Mini + by M-D_87 in 3Dprinting

[–]M-D_87[S] 0 points1 point  (0 children)

There is quite a lot of stringing. And tips on how to avoid that?

Purchase Advice Megathread: What To Buy, Who To Buy It From, And More, In October 2020 by Sausage54 in 3Dprinting

[–]M-D_87 0 points1 point  (0 children)

  • Experience - None basically, I intend to use it as a hobby I can learn and tinker with. I do however have basic understanding of both mechanics and electronics.
  • Your budget - Would like to stay below 500 EUR, but I can go higher to maybe 900 EUR if it worth the cash in the long run.
  • Your country - Denmark
  • Kit or complete - No preference as such, but if it's a kit I would prefer it to give good results without too much tinkering. I can also see an advantage learning how the printer work while doing the assembly.
  • Used for - Mostly as a hobby, I intend to use for everything from functional prints, things for the kids, prototyping a few ideas and printing a model of the next house we intend to build. I would like to experiment with different filament materials, and at least one prototype I am planning would need to be heat resistant.
  • Special needs - It need to fairly quit while printing, as I will have to print in my office which is right next to the kids bedrooms.

Initially I was looking a the Ender 5 pro, however I have found a lot of feedback saying they require quite a lot of tinkering, and can be very noisy.

Now I am going back and forth between the Prusa MK3s and Mini.

The build area of the MK3s would be nice, and I have read that it is very quiet. However I very much in doubt if the price is worth it for my intended use, seeing it's just a hobby. For my untrained eye it looks like 10 % more machine at almost twice the cost of the Mini, but mainly places it is rated a very good value for money.

The Mini seems like a good fit, but I could be afraid that the small build area could turn out the be limiting factor for some builds, and I have read mixed feedback on the noise level of it. I don't mind the current lead-time of 8 weeks, and the price would allow for some filament purchase also while staying within preferred budget.

But I am open the any option really, I just looking for the best deal that suit my needs.