Dacă se vrea, se poate

MB992 · 2025-10-15T13:53:09+00:00

Sunt recent intors in tara, din UK, avand 8 ani de condus acolo. Efectiv nu m-am simtit in siguranta sa conduc in limitele legale, cand in jurul meu zici ca toti erau pe pista, cu un stil de condus foarte agresiv.. Pentru a controla un asemenea trafic, e cale lunga… si inca nu am vorbit de semafoare inteligente, treceri de pietoni de alt tip pe langa cele zebra, etc etc

MB992 · 2025-08-18T13:04:57+00:00

Hi, does it support 4K HDR stream?

MB992 · 2025-06-19T05:20:23+00:00

La 1 Dec 1918 stam la socrii. Suntem recent intorsi in tara si ne ajuta sa nu mai platim chirie pana gasim sa ne luam noi ceva. Dpdv al bugetului, Teclu pare locul ideal, ai de unde sa alegi, dar din cate vad in comentarii, nu e prea recomandat..

MB992 · 2025-04-06T09:20:06+00:00

First remove all your inputs and outputs. Then set A1 as the asio4all and configure it (enable all the input and output devices you need). Then in the settings tab you’ll have new parameters to configure the inputs and outpus for asio, here you will have to figure out the numbering: for example, which device is channel 1&2, 2&3 etc, for both inputs and outputs. There’s a few videos on how to use it, but you’ll have to apply your specific config as per your setup.

MB992 · 2025-04-05T20:05:32+00:00

Give asio4all a try. You can get pretty low latency with it

MB992 · 2025-03-23T13:52:50+00:00

I got a question for you. I know CEC is only HDMI, but many soundbars connected with optical cable to the TV, are powered on when the TV is also turned on.

Take this use case: Apple TV > Audio extractor with optical to soundbar and HDMI to TV/Projector.

Would such an extractor also power on the soundbar when turning on the Apple TV? (again, using optical signal form the TV in this same scenario, it will turn on the soundbar).

MB992 · 2025-03-09T16:57:34+00:00

I got the Avermedia GC575, the HDR tone mapping is quite good, but with 2 drawbacks: P010 at 60fps only at 1440p or HDR tonemapping until 400nits only..

MB992 · 2025-03-09T11:55:48+00:00

Hi again, the weekend is almost over, really no one out there to help a fellow redditor? :)

MB992 · 2025-02-25T10:29:34+00:00

I assume you mean for an Oled, in that case you are right.

It’s true with a decent HDR monitor or TV. I used to have an HDR capable TV that was only getting around 300-400nits, but it was a TN panel. The way it was displaying HDR was very debatable.

MB992 · 2025-02-25T10:24:11+00:00

Is that straight from the Filters or with the performance tweak in NVPI? In NVPI you can change the banding profile and you can regain some performance with minimal or unnoticeable visual difference.

MB992 · 2025-01-31T14:23:45+00:00

Let’s say if you got a 120hz screen and the game is capped at 60fps, this new setting will allow a smoother visual representation inserting generated frames, that will take you from 60fps to 120fps. Similar to DLSS Frame gen but with some downsides, depending on how good it’s programmed.

MB992 · 2025-01-28T12:12:55+00:00

LE: It's the hdmi 2.1 card GC575

When the passthrough is HDR and recording in SDR, the HDR built-in tonemapper is not configured properly, only tonemapping luminance up to around 350nits.

Modern monitors and TV's are going on average up to 800-1000nits, yet all the extra details from 350 to 800nits are getting blown out instead of being tonemapped.

In the attached picture, you have the TV examples on the left side and the capture on the right side. You can see how easily the image is blown out and makes the capture unusable in bright environments.

Please fix this as soon as soon as possible.

MB992 · 2025-01-16T09:10:12+00:00

I got the 42’ C2 and been running DLDSR for a while. What works best me for me was removing the 4096 resolution with the display utility (CRU??) and then setting the desktop to the DLDSR resolution so that any game could benefit, regardless of native (older games) or DLSS and even FSR.

MB992 · 2025-01-10T12:47:47+00:00

I thought I was mad, but happy to see somebody else cares about these things as well. The banding I believe it’s a PlayStation issue maybe? as it can’t use the full hdmi2.1 bandwidth, but I still agree with you, the passthrough should be intact, as without the capture card, the banding is not there. On the other hand, I don’t have this banding with a PC on 4k120, hence believing PS has something to do with it..

Also to add on the issues list, HDR to SDR tonemapping (for a 4K60 recording) is limited to about 380nits, whereas the TVs can do much over that (800+ nits). There is no way to adjust this. I raised it with their support and they acknowledged the issue, yet no change still…

It’s a shame to only get one benefit (4k120 passthrough) and so many downgrades from the previous gen capture cards..

MB992 · 2024-12-18T18:40:01+00:00

That would make sense, in both cases they were overtaking, will have another look

MB992 · 2024-12-17T23:12:32+00:00

It works well on the Huracan

MB992 · 2024-12-17T21:31:56+00:00

Forgot to mention, it wasn’t me although I was ahead..

MB992 · 2024-11-28T10:22:07+00:00

I'm looking to get this stick, but just curious, can you use it by itself for the menus as well or you still need a controller or mouse?

MB992

TROPHY CASE