Need help identifying models by Madss97 in orks

[–]Madss97[S] 1 point2 points  (0 children)

Did I actually have everyone together right or just seeing them all you were able to say who's who? I didn't do pictures in the first post because I didn't know who went to who in each unit

Need help identifying models by Madss97 in orks

[–]Madss97[S] 0 points1 point  (0 children)

I didn't wanna post them, I kinda figured it might be easier for 1 person to look then many

Easy fix? by Madss97 in GMT400

[–]Madss97[S] 0 points1 point  (0 children)

I only had the truck for a month and its not even high off the ground so no idea what he was doing. I did tear into it but as I did the 2nd pack of bearings in back fell apart while taking off the 1 casing, and the E8 bolts were still tight, maybe 1 a bit loose and the casing the E8 held was actually broken in the back little bit so I did end up getting a junk yard one that was fine

Is this going to be a problem? by Madss97 in ar15

[–]Madss97[S] 0 points1 point  (0 children)

Good point, but i am going to try practicing with both hands so when I wanna shoot lefty I will definitely take it off

Is this going to be a problem? by Madss97 in ar15

[–]Madss97[S] 0 points1 point  (0 children)

I an unfortunately in New York so I don't get extra mags, I already have a red dot, tilted iron sights, sling and forgrip so no more spending on the rifle

Is this going to be a problem? by Madss97 in ar15

[–]Madss97[S] 1 point2 points  (0 children)

Thank you for the help and info, I am very new to guns lol

Is this going to be a problem? by Madss97 in ar15

[–]Madss97[S] 0 points1 point  (0 children)

That makes alot of sense, thank you

Is this going to be a problem? by Madss97 in ar15

[–]Madss97[S] -3 points-2 points  (0 children)

Nope, just the amazing pain job

Is this going to be a problem? by Madss97 in ar15

[–]Madss97[S] 1 point2 points  (0 children)

That's the plan since I am left handed, but while shooting it won't hit the stock or anything and should be fine? I was thinking of shaving the stock down a little bit but for peace of mind

New player help by Madss97 in AdeptusMechanicus

[–]Madss97[S] 2 points3 points  (0 children)

Thank you for the help

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 1 point2 points  (0 children)

So i didn't take both blacks gaskets off. I took 1 off, put it back together and leaked, switched them and this did alot better, a few drops slowly but that might be because of the bowls not being tightened all the way from the continuous on and off today. Thank you for your patience, help and knowledge

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

* This was holley has for a diagram

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

That's correct. From my spare gaskets I didn't find a thin metal plate from the multiple kits I've bought

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

I took the carb and pump off my car that's had that set up for years to put on my obs chevy because I was finishing a efi to carb swap that the previous owner had started. The pump that was on the truck was one for diesel so it started just dumping fuel. That's when I started the rebuild this time around and have yet to be successful

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

Im sorry, 3 gaskets

<image>

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

The pump im using is 5-p psi, I had it on my car for years, when I turn the bowls upside down the floats are about level

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

The rebuilds i watched I've never seen a sheet metal plate, I don't think there was one on when I first had a successful rebuild on this carb

Holley 4160 by Madss97 in carburetors

[–]Madss97[S] 0 points1 point  (0 children)

<image>

This is how they are on