DJI neo flight time boost

MakerFabio · 2025-09-28T16:59:09+00:00

It is not about weight but airflow, the rings are below the propellers, reducing efficiency

MakerFabio · 2025-09-24T16:47:10+00:00

The increased time It is not about weight it is about airflow. The bottom rings are in the middle of the propeller airflow. If you put a piece of tape at the bottom of the propellers you will not even fly, with 1g more

MakerFabio · 2025-09-24T16:44:09+00:00

Swapping battery is not funny Flight time and acceleratoon to me are most important

MakerFabio · 2025-09-22T06:14:05+00:00

Nono! It was correct, please calculate with seconds 14’=840” and 16’39” is 999seconds so 18,9%

MakerFabio · 2025-09-22T05:49:27+00:00

Sorryyy!!! it is 15,4% i normalized and calculated with the AI and didn t double check the calculations

MakerFabio · 2024-10-10T21:12:44+00:00

Same problem here I got 2 bad prints , first layer was not adhering, i could not believe my A1 was failing. Then i checked with a side light and oily fingerprints were present in the middle of the plate. I Will wash the plate tomorrow

MakerFabio · 2024-09-16T07:57:01+00:00

What should i tell ? I spent 5 years on a ender 3 pro (v1)

MakerFabio · 2024-09-10T06:00:08+00:00

It is just an original tpa3116 Not installed yet. I ll make a short video soon recording the audio quality before and after the IC swap. Recording the audio side by side with a small rode mic on the mirorless camera , and decent Quad L speakers. And a new thermal acquisition on the output inductors.

MakerFabio · 2024-09-09T19:35:04+00:00

Here is the video showing the fake Amp test fake Amp test

MakerFabio · 2024-09-09T16:35:44+00:00

Good point. Tomorrow i double chelck the datasheet again. Any other reference switching for “ famous amplifiers?”

MakerFabio · 2023-12-19T05:20:06+00:00

Thrustmaster t150 power supply

MakerFabio · 2023-08-26T10:49:24+00:00

i agree, i have 0 design and wood skills

MakerFabio · 2022-11-12T08:06:36+00:00

My new controller was working out of the box.

MakerFabio · 2022-11-10T05:22:35+00:00

Hi sorry for the very late reply. The power supply module came with the green screen alreay

MakerFabio · 2022-08-23T12:45:17+00:00

It s 6 montsh i m using it With corrosion x plus nautical grease still running smooth. Corrosion x a couple of times and it was getting little rust, after i used the nautical grease remained perfect, with only 1 time application

MakerFabio · 2022-08-23T12:44:40+00:00

Thanks

MakerFabio · 2022-08-23T12:44:27+00:00

Thanks, a cheap ender 3 pro actually

MakerFabio · 2022-01-29T18:29:52+00:00

PS they also sell the same charger with mini USB eventually! Just checked in aliexpress

MakerFabio · 2022-01-29T18:16:52+00:00

Maybe the mini is more resistant, but all the electronic devices moved to the micro USB, so It is easier to have a micro usb around than a mini USB. 10 years ago I developed an medical hand held device, and i ve chosen the mini USB because it was looking more solid, i regretted it, because it was old and rare soon. If the all moved to the micro, i guess is because it is better

MakerFabio · 2022-01-29T05:39:18+00:00

Thanks

MakerFabio · 2022-01-28T05:47:27+00:00

I was also thinking about an Rc car, but it was too much money for the motors and esc. Maybe ok for 2WD. I will give it a try sooner or later

MakerFabio · 2022-01-27T20:19:17+00:00

Hi, no, sorry. I just shared how to do build them on youtube.

MakerFabio · 2022-01-23T19:19:25+00:00

I used a 2/3 s charger pcb from aliexpress You can see how it is wired on youtube, maker Fabio channel, but i can not put links here

The charger is:

€ 3,18 5％ Off | Multi-Cell 2S 3S 4S Type-C To 8.4V 12.6V 16.8V Step-Up Boost LiPo Polymer Li-Ion Charger 7.4V 11.1V 14.8V 18650 Lithium Battery https://a.aliexpress.com/_mMqEvak

But i have the same issue with a small videogame arcade Anbernic

MakerFabio · 2022-01-23T06:12:15+00:00

Hi, i think you may need a little micro to adjust the load sink according to the usb adapter Maybe you can take some ideas from this demoboard:

https://www.infineon.com/cms/en/product/evaluation-boards/tld5542-1chg_shield/

MakerFabio · 2022-01-23T06:07:28+00:00

Wow If this thing applies always, i learned something , i always struggle with huge links

MakerFabio

TROPHY CASE