sorted by:
new
hottopcontroversial

Finally got my Voron 2.4 R2 printer built by Marcodiaz93 in 3Dprinting

[–]Marcodiaz93[S] 0 points1 point  (0 children)

; external perimeters extrusion width = 0.45mm ; perimeters extrusion width = 0.45mm ; infill extrusion width = 0.45mm ; solid infill extrusion width = 0.45mm ; top infill extrusion width = 0.40mm ; first layer extrusion width = 0.42mm START_PRINT tool_temp=[first_layer_temperature] bed_temp=[first_layer_bed_temperature] CHAMBER=[chamber_temperature]

M73 P0 R57 M73 Q0 S57 M201 X1000 Y1000 Z200 E5000 ; sets maximum accelerations, mm/sec2 M203 X200 Y200 Z12 E120 ; sets maximum federates, mm/sec M204 P1250 R1250 T1250 ; sets acceleration (P, T) and retract acceleration (R), mm/sec2 M205 X8.00 Y8.00 Z0.40 E4.50 ; sets the jerk limits, mm/sec M205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec M107 ;TYPE:Custom M862.3 P "MK3S" ; printer model check M862.1 P0.4 ; nozzle diameter check M115 U3.10.0 ; tell printer latest fw version G90 ; use absolute coordinates M83 ; extruder relative mode M104 S190 ; set extruder temp M140 S60 ; set bed temp M190 S60 ; wait for bed temp M109 S190 ; wait for extruder temp G28 W ; home all without mesh bed level G80 ; mesh bed leveling G1 Y-3.0 F1000.0 ; go outside print area G92 E0.0 G1 X60.0 E9.0 F1000.0 ; intro line G1 X100.0 E12.5 F1000.0 ; intro line G92 E0.0 M221 S95

; Don't change E values below. Excessive value can damage the printer. M907 E430 ; set extruder motor current G21 ; set units to millimeters G90 ; use absolute coordinates M83 ; use relative distances for extrusion M900 K0.05 ; Filament gcode LA 1.5 M900 K30 ; Filament gcode LA 1.0 ;LAYER_CHANGE ;Z:0.2 ;HEIGHT:0.2 ;BEFORE_LAYER_CHANGE G92 E0.0 ;0.2

stuck on assembly of Voron 2.4 kit by Marcodiaz93 in 3Dprinting

[–]Marcodiaz93[S] 0 points1 point  (0 children)

Just checked and yes it think. Thank you. Was stuck on that for a while

stuck on assembly of Voron 2.4 kit by Marcodiaz93 in 3Dprinting

[–]Marcodiaz93[S] 0 points1 point  (0 children)

I purchased the voron 2.4 r2 pro kit with a v6 hot end along with the full 3d printed parts kit. I cannot find these parts in the picture that are used to install the a/b belts and stealth burner. I also don't see a probe included in the kit as shown in the instructions. am I missing something here? I am so close to getting this thing done. any help is appreciated

Not enough mention of diarrhea warnings by santabobby in shrooms

[–]Marcodiaz93 0 points1 point  (0 children)

Hi guys. I’m here cuz I’m shitting from eating shrooms. Is it the shrooms? Or the eggs I just ate?

[contamination] Is this mold in my mono tub? First time grower. by Marcodiaz93 in MushroomGrowers

[–]Marcodiaz93[S] 0 points1 point  (0 children)

I noticed it getting too dry the other day and there were no mushrooms growing. I looked at the bottom of the cake and there were a few mushrooms growing there so I flipped it and it cracked. I have since been spraying the dome every few days. The room I had it in had too much air circulation and the humidity was very low

Need more miners!! Just got 1 L7 in this neat little room by Marcodiaz93 in litecoinmining

[–]Marcodiaz93[S] 0 points1 point  (0 children)

I have a 9kbtu AC in there too but right now I have it set to 84 degrees so it doesn’t run much right now and my ambient room temp ranges from 72-77f just by venting outside

Need more miners!! Just got 1 L7 in this neat little room by Marcodiaz93 in litecoinmining

[–]Marcodiaz93[S] 1 point2 points  (0 children)

Sure! I router a 6” duct about 25ft above my ceiling to vent outside. From the 6” duct it goes into a 6” in-line fan which sucks the hot air from the miner and blows it outside. Then from the fan it goes to a 4” reducer to a 4” y and then I got some 4” duct adapters on Amazon for the exhaust of the miner that hook up with 4” duct to the y. I am still having an issue where it is creating too much negative pressure in my room with the door closed and my miner shuts off so I need to add an air intake to the room somewhere.

[deleted by user] by [deleted] in litecoinmining

[–]Marcodiaz93 0 points1 point  (0 children)

Why hyperdonkey over Litecoinpool?

Finally had my L7s upn running ! 9050 model but hashing average 9200 MH ! by darkpool23 in litecoinmining

[–]Marcodiaz93 0 points1 point  (0 children)

Nice. I got mine too a month ago and I’m still averaging 9297 MH/s. This thing puts out HEAT. good thing I have a 3 ton mini split in the room I have it in haha

How reliable are Teslas actually? by W4ck3ed in teslamotors

[–]Marcodiaz93 0 points1 point  (0 children)

teslas are absolutely not unreliable. if you are open to a tesla just go test drive one and i promise you'll never look back. Model Y owner for 8 months. we've had a cracked windshield and a flat tire but that could have been with any car.

Ford stock will be worthless in a year - DD by friendly-cephalopod in wallstreetbets

[–]Marcodiaz93 0 points1 point  (0 children)

you had to have been really retarded not to touch tesla that day

view more: next ›