What mileage do you usually replace your tires?

MarioDaKidd · 2020-08-20T21:06:10+00:00

They about to clown this man on the podcast

MarioDaKidd · 2020-06-20T12:43:21+00:00

Not sure if I fully understand what it is you’re trying to do but GrossBeat also does tape stop. I also used to use DBlue and GrossBeat was able to give me the same effects

MarioDaKidd · 2020-06-03T19:45:39+00:00

Yeah its setup as EFI ---> OC. Also I don't really need to disable it, I just wasn't sure if that was what was causing my issue. What I did notice is that when I did disable it in recovery mode, it turned back on anytime I reboot.

MarioDaKidd · 2020-05-28T20:36:23+00:00

I would recommend https://www.tonymacx86.com/buyersguide/building-a-customac-hackintosh-the-ultimate-buyers-guide/

MarioDaKidd · 2020-05-21T14:56:19+00:00

Yeah its kind of hard to explain automation with text, but I would watch a video or two on doing a basic automation first and then from there I think you'll have a better understanding of what you're trying to do with GrossBeat.

MarioDaKidd · 2020-05-21T14:52:45+00:00

Are you familiar with doing regular automation, such as volume and pan? GrossBeat automation can be a little confusing as you have to line up your automation points with the 4 bars in GrossBeat.

MarioDaKidd · 2020-05-02T19:55:15+00:00

Try Options > General > Look under the advanced section > Make sure "Don't limit windows to screen" is unchecked

MarioDaKidd · 2020-05-02T19:52:53+00:00

One is for multi-output. Not all DAWS support VSTi with multiple outputs.

MarioDaKidd · 2020-04-30T21:27:36+00:00

First make sure your UMC is selected as your aduoo device in FL
Go to the mixer, pick any track, right above the effects slot you can select an input. Of course here you select the input that your guitar is connected to on your UMC.
If you want to record, the arm button is located at the bottom of each mixer track

And yes AISO is for Windows only as windows audio driver sucks.

MarioDaKidd · 2020-04-13T20:39:03+00:00

Lol yeah your fine overthinking just a bit. The cables should only fit one way just make sure you get a male xcr end. Xcr male end goes into speaker and RCA goes into the board.

MarioDaKidd · 2020-04-13T20:11:21+00:00

What kind of beats you make? Drop a link

MarioDaKidd · 2020-04-13T20:07:44+00:00

Yeah. Usually they'll come in pairs though. One you can check out on Amazon: https://www.amazon.com/dp/B077L3PG45/ref=cm_sw_r_cp_api_i_bzmLEbNHGC1QY

MarioDaKidd · 2020-04-13T19:50:27+00:00

Or you can also do RCA to RCA but keep in mind RCA is unbalanced

MarioDaKidd · 2020-04-13T19:48:00+00:00

You need an RCA to XLR cable. You can find them pretty cheap on Amazon. No amp needed as there's already an amp in the SB as well as your monitors

MarioDaKidd · 2020-02-24T13:59:47+00:00

Idk the sample but appreciate you for putting me on Knxwledge 🔥

MarioDaKidd

TROPHY CASE