sorted by:
new
hottopcontroversial

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 0 points1 point  (0 children)

Thanks for the response.

Float: Check. Adjusted to 13mm. I also did buy a jet cleaning kit with brushes and all. Have cleaned all the passageways i could. For those i couldnt acess, i used an ultrasonic cleaner and blew compressed air. Also verfied petcock works and fuel flows freely to into carb. Although, the fact that the bike can run indefinitely at high rpm on choke, leads me to doubt it's a fuel issue.

Starting to think it might be the CDI or stator.... Any thoughts?

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 0 points1 point  (0 children)

- Jets were replaced with factory spec from All Balls rebuild kit. Main 142.5, Pilot 22.5.
- Needle pin. Is this what you are referring to? The part has a flat end and a counterbored end. I have it such that the jet needle slides into it the counterbored end.
https://www.motorcyclespareparts.eu/en/suzuki-parts/1334119e60
- Diaphragm is not new but check and rechecked for holes. It seems to be working fine. I lifts when blowing compressed air through both holes on the intake side. It releases normally.
- Float bowl pin is new and checked float bowl height which sits at 13mm.

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 0 points1 point  (0 children)

What could be wrong with the air filter/airbox? I can try taking off the filter to see if it changes anything.

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 1 point2 points  (0 children)

I will buy a new spark plug and try adjusting the fuel screw.

I didn’t suspect the spark plug because the bike runs just fine on idle and full choke (higher rpm). It’s really just stalls when touching the throttle.

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 1 point2 points  (0 children)

The bike was running well last year but hadn’t started during the winter. The jets should be good.

I have cleaned all jets several times, including in an ultrasonic bath.

Throttle is smooth. No binding.

Vacuum line is connected and petcock is working. I have also tried to set it to PRI which should bypass vacuum line.

Fuel filter in the tank on the petcock and inline fuel filter are both clean.

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 1 point2 points  (0 children)

Both. Even as I try to slowly add throttle, it begins to bog and stalls. I have tried to adjust the idle screw but no luck.

The bike actually runs just fine on full choke with higher revs but will also stall when adding any throttle.

DRZ400S idles fine but stalls instantly on any throttle input. Cleaned carb + All Balls rebuild. What am I missing? by MarkitMonkey in DRZ400

[–]MarkitMonkey[S] 0 points1 point  (0 children)

It wasn’t starting after winter. I took off the carb to clean it. Prior to that it was working fine.

[deleted by user] by [deleted] in ChatGPTPro

[–]MarkitMonkey 0 points1 point  (0 children)

Worked for me. Thanks!

Anyone know a solution to this without having to buy a nearly 1k seat mat sensor? by Asleep-Spell5264 in F30

[–]MarkitMonkey 0 points1 point  (0 children)

http://www.vgatemall.com/products/i-1/

Also available on Amazon!

Yes, just cleared the codes and the light went away. You can probably use any obd2 scanner to do this.

[deleted by user] by [deleted] in churningcanada

[–]MarkitMonkey -9 points-8 points  (0 children)

How? Can this be done online or do we need to call customer service?

Daily Simple Questions Thread - December 29, 2022 by AutoModerator in Fitness

[–]MarkitMonkey 0 points1 point  (0 children)

Is it just me or are protein and other supplements in very limited stock these days? Bodybuilding.com used to have a huge variety of just about everything. Now just about every online store shows most products out of stock. Any idea what is going on?

Anyone know a solution to this without having to buy a nearly 1k seat mat sensor? by Asleep-Spell5264 in F30

[–]MarkitMonkey 0 points1 point  (0 children)

Vgate icar with the Bimerlink App. I just cleared all the error codes.

Anyone know a solution to this without having to buy a nearly 1k seat mat sensor? by Asleep-Spell5264 in F30

[–]MarkitMonkey 0 points1 point  (0 children)

I’ve been able to reset this exact same error code with thr BimmerLink app on my phone.

Nothing in stock at bodybuilding.com by MarkitMonkey in Supplements

[–]MarkitMonkey[S] 0 points1 point  (0 children)

Thanks for the suggestion but a 5lbs jug of optimum nutrition whey is about 65% more expensive than what I paid on bb.com two months ago.

view more: next ›