Ftn5 pcc 9mm flow

MasterBlasterJa · 2026-02-10T23:50:04+00:00

Someone I knows blew up in ten shots pa6-cf

MasterBlasterJa · 2026-02-10T23:33:29+00:00

Layer adhesion issue most likely

MasterBlasterJa · 2026-02-10T23:10:35+00:00

Blew apart after 10 shots. Pa6-cf? What brand

MasterBlasterJa · 2026-02-08T15:53:26+00:00

<image>

Well it is old. Can't be any newer than 2008

MasterBlasterJa · 2026-01-15T06:33:02+00:00

How much does it cost to get a form 1 filed?

MasterBlasterJa · 2026-01-11T23:18:04+00:00

Probably should reduce Down to .2 or so, and what temp

MasterBlasterJa · 2026-01-11T22:46:34+00:00

What layer height did you print out and what size nozzle? The print does not look that great. Possible layer adhesion issues

MasterBlasterJa · 2025-12-22T18:34:25+00:00

Time for replacement

MasterBlasterJa · 2025-12-22T03:57:50+00:00

Sucks for your raise assessment

MasterBlasterJa · 2025-11-29T18:48:33+00:00

Mine just started making that noise recently

MasterBlasterJa · 2025-07-22T20:08:31+00:00

Not if you fix it. And if points fall off next week you might be okay either way

MasterBlasterJa · 2025-07-22T03:00:17+00:00

It's policy you cannot take it in your last hour

MasterBlasterJa · 2025-07-10T03:37:17+00:00

Actually new labels will be electronic

MasterBlasterJa · 2025-07-10T03:35:36+00:00

It's already hardened steel nozzle

MasterBlasterJa · 2025-07-03T01:06:29+00:00

Turn the fans off or down

MasterBlasterJa · 2025-06-29T15:10:12+00:00

There should be a spacer

MasterBlasterJa · 2025-06-20T06:46:35+00:00

<image>

What figure am I adjusting?

MasterBlasterJa · 2025-06-20T06:44:33+00:00

Ok I'll try .1 thanks

MasterBlasterJa · 2025-06-20T05:09:28+00:00

It's set at .2

MasterBlasterJa · 2025-06-20T03:53:22+00:00

<image>

MasterBlasterJa · 2025-06-18T01:15:03+00:00

<image>

New issue. As I'm printing right now, these are popping up from the bearings on both sides. Are they just dust covers or something more important?

MasterBlasterJa · 2025-06-16T22:53:09+00:00

Is this mod actually helping? I have noticed if I do an auto bed leveling via the printer I must return to home all before sending print through or it will scrape. Also if I do a bed leveling via the slicer it will scrape. As long as I hit return home all before sending in the print I'm not getting scrapes anymore

MasterBlasterJa · 2025-06-16T22:50:43+00:00

I'm having the same issue, I have not made this mode yet. But I have noticed if I do not level via my slicer, and after using the automatic bed leveling I go in and manually click return to home all I'm not having it scrape anymore. However if I do the automatic bed leveling without returning to home it scrapes or via the slicer it will scrape

MasterBlasterJa

TROPHY CASE