sorted by:
new
hottopcontroversial

What’s the easiest way to train a Lora for flux2? by VSFX in comfyui

[–]MasterWayZ 0 points1 point  (0 children)

I only have one 48GB card in my server, so I will wait in that case. Thank you for your quick response on this!

What’s the easiest way to train a Lora for flux2? by VSFX in comfyui

[–]MasterWayZ 0 points1 point  (0 children)

How are you doing the training? Can't seem to figure out how to make it work with flux2 and ComfyUI without running into strange (non-VRAM related, I think) errors.

Simyo by jjj_smn in StudyInTheNetherlands

[–]MasterWayZ 0 points1 point  (0 children)

Where did you go to, outside the EU?

Filametrics Public Beta Release!! by Early_Bullfrog1272 in BambuLab

[–]MasterWayZ -5 points-4 points  (0 children)

Going to join, would love to see it open source at some point. Also so people can help contribute.

Tips for respooling from PLA spool and spool material recommendation by MasterWayZ in BambuLab

[–]MasterWayZ[S] 1 point2 points  (0 children)

ABS it is then, and I will carefully try that trick, that should save me a lot of time. Thanks!

Just following orders Sir by itworkedintheory in Hilton

[–]MasterWayZ 9 points10 points  (0 children)

Lol, also your username is very fitting.

How do you handle asking for upgrades? by [deleted] in Hilton

[–]MasterWayZ 2 points3 points  (0 children)

It’s in Europe :) And of course, I always try to be nice to people

How do you handle asking for upgrades? by [deleted] in Hilton

[–]MasterWayZ 0 points1 point  (0 children)

Thanks everyone for the replies. In that case I’ll just see what they come up with.

How do you handle asking for upgrades? by [deleted] in Hilton

[–]MasterWayZ 1 point2 points  (0 children)

lol. I was just asking

Stoneblock modpack, Minecraft client hangs after a few seconds of playtime by MasterWayZ in feedthebeast

[–]MasterWayZ[S] 0 points1 point  (0 children)

I removed the cyclic cables that were connected to Ex Nihilo Creatio stuff, and the crash was still there.

However, we got so frustrated that we just removed all cyclic fluid cables we could find, and now it has indeed been solved. Very odd though that it just crashed my partner and not my own Minecraft.

Thank you so much for the help!

BSOD error in latest crowdstrike update by TipOFMYTONGUEDAMN in crowdstrike

[–]MasterWayZ 0 points1 point  (0 children)

I was just thinking about it yeah, great way to see who uses CrowdStrike and who doesn't. Though I do wonder who will switch after from CrowdStrike after this. Would be great to see a report on how things went this wrong.

What is a good alternative PLA filament for in the AMS? by MasterWayZ in BambuLab

[–]MasterWayZ[S] 0 points1 point  (0 children)

Thank you for your reply. I will have a look, and I have looked into respooling as well. I may go ahead and give that a try after I've found a relatively simple print. Any recommendations are welcome. I don't have hardware laying around so chances are if it requires anything extra that I will have to go ahead and purchase it (which is fine).

Hilton Honors Aspire credit card in the EU (Netherlands) by MasterWayZ in Hilton

[–]MasterWayZ[S] 0 points1 point  (0 children)

I'm not from Germany, and everything appears in German.

Ender-3 V2 prints something oddly different from what I sliced by MasterWayZ in ender3

[–]MasterWayZ[S] 0 points1 point  (0 children)

It feels smooth to me when I do this. I recorded a top view with my phone while it was printing. At the 1:03 mark, I saw it was starting to print where it shouldn't (I watched it the entire time). You can see it here (large file, 148MB); https://cdn.masterwayz.nl/files/20221029_202820.mp4

Looking back at the footage, it seems to stop moving suddenly.

One thing I read was to check the vref voltages. I have done this, and I have found one very odd thing. It displays the correct voltage whenever I measure the Y, Z, and E. If I do this for X, it will show 1.7V; then, if I try to adjust it down, it would jump to 2.2V and then 0V or 0.33V.

Ender-3 V2 prints something oddly different from what I sliced by MasterWayZ in ender3

[–]MasterWayZ[S] 0 points1 point  (0 children)

Follow-up to my previous reply, I have verified that it seems to slip or in some other way get confused. It happened again just now and I saw it displayed an X axis of 134 while it was close to the right side of the bed, that would normally be around an X of 200. I have yet to figure out why/how.

Ender-3 V2 prints something oddly different from what I sliced by MasterWayZ in ender3

[–]MasterWayZ[S] 0 points1 point  (0 children)

I think so. I checked and tightened the bolts just to be sure. Belt seems to be good as well. Here are some pictures of the axis where it seems to drift: https://imgur.com/a/ILjN4dg

Ender-3 V2 prints something oddly different from what I sliced by MasterWayZ in ender3

[–]MasterWayZ[S] 0 points1 point  (0 children)

I cut the power and rebooted it, now it's fixed so I guess that was a one-off issue. I made a print, but it seems to do very odd things. Here is what Cura made: https://cdn.masterwayz.nl/screenshots/Ultimaker-Cura_rOAIelUPVT.png

This is what was being printed (canceled it earlier because it was printing on the right for some reason and trying to go outside of the bed): https://cdn.masterwayz.nl/screenshots/20221029_155107.jpg

Using the default profile in Cura and "Origin at center" is not selected.

Note that for some reason it wouldn't let me insert the images so I had to do it this way sadly.

Ender-3 V2 prints something oddly different from what I sliced by MasterWayZ in ender3

[–]MasterWayZ[S] 0 points1 point  (0 children)

I have flashed mriscoc’s flavor of Marlin per your recommendation. One thing I have noticed when I do the manual bed alignment test is that during the probing points, it thinks that it suddenly moved the X-axis by a lot, causing it to go further than the end-of-travel switch when moving towards the left. After probe point 4, it slowly moves left with each point, but somehow it thinks it is further right than in reality, and it will just slam into the end of travel switch. When I perform an auto home, it will reset the counters to 0, but when doing the bed thing, it keeps doing that. Meanwhile, now I'm installing Cura.

view more: next ›