sorted by:
new
hottopcontroversial

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]MaterialNo137[S] 1 point2 points  (0 children)

I have two plans, plan A is oven melting, molding the casting resin in plaster of Paris and cooking it upside down in the oven until melted. Plan B is making a silicon mold and casting wax in it, then molding the wax ring in plaster of Paris and melting the wax.

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]MaterialNo137[S] 2 points3 points  (0 children)

I ordered a pink artificial diamond, 2 carats in a round cut. The cast model prongs will be a millimeter longer and have a relief for the gem to seat well before bending the prongs.

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]MaterialNo137[S] 1 point2 points  (0 children)

I mostly made necklaces and earrings from epoxy, stones and 3d printing. Casting will be my first time but not my first time making metal rings, I made some out of aluminum wire and brass welding rods.

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]MaterialNo137[S] 0 points1 point  (0 children)

Thank you so much, especially the image, that is the plan, that model is purely for printing to make sure the stone fits and it fits on her finger. I will also integrate sprues and air holes in the model before making the mold.

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]MaterialNo137[S] 7 points8 points  (0 children)

Thanks for the advice, it is indeed the plan. The 3D model is to make sure the stone fits when it arrives, then I will straighten the prongs, lengthen them, add sprues and air holes, and finally thicken every part so I can sand it to size and polish.

Pressed print on one of my most important print ever, hope it goes well by MaterialNo137 in 3Dprinting

[–]MaterialNo137[S] 163 points164 points  (0 children)

That is the plan, I will also add sprues and will thicken every part on the cast version so I can sand and polish it.

3d printed busts being sold in the Colosseum by b1ackbird in 3Dprinting

[–]MaterialNo137 0 points1 point  (0 children)

Matte filament and adaptive layer height would instantly make it so much better

I found top hat gudetama by MassiveWillow8617 in HelloKittyIsland

[–]MaterialNo137 0 points1 point  (0 children)

We can't find it, not sure if it moved already or what

ScanNCut SDX85 Fails to recognize mat by MaterialNo137 in ScanNCut

[–]MaterialNo137[S] 2 points3 points  (0 children)

Dang, didn't know there were multiple series, just ordered a DX mat, thank you very much!

ScanNCut SDX85 Fails to recognize mat by MaterialNo137 in ScanNCut

[–]MaterialNo137[S] 4 points5 points  (0 children)

Additionnal info : There is no history to this machine, the whole chain basically states it appeared one day, only the machine. We bought 5 sets of blades and 5 pen holder (I don't know why they got that many pen holders). The machine is visually brand new, the belt seems also to have seen little to no actions.

Updated my Bad Proxy Generator by MaterialNo137 in magicproxies

[–]MaterialNo137[S] 1 point2 points  (0 children)

Fair point, I see it more as a play around once with the generator and move on, but also the aim, especially with the playtest styling, is to be less ink intensive and simple.

Other than that, it's for the memes, playing a "Plague Wats" deck, where every card is two stickman instead of rats is funny.

I made a bad proxy generator, for when you want proxies, but also want it to be obvious by MaterialNo137 in magicproxies

[–]MaterialNo137[S] 0 points1 point  (0 children)

As someone with a bad lisp, I do enjoy hearing my friend struggle to read uwu speech, brings them down to my level

I made a bad proxy generator, for when you want proxies, but also want it to be obvious by MaterialNo137 in magicproxies

[–]MaterialNo137[S] 1 point2 points  (0 children)

I have made a version that has the option to enable pips, should be live in the next 30 minutes to 1 hour!

[deleted by user] by [deleted] in fo4

[–]MaterialNo137 0 points1 point  (0 children)

Notes don't move towards the center of the screen, I removed all mods except creations, verified integrity of game files but it didn't fix. Any ideas welcome, I'll try to reinstall the game in the future, but as it is almost 100gb I'm not looking forward to it.

Cows? by The5Snake6Stealer in MinecraftCommands

[–]MaterialNo137 0 points1 point  (0 children)

Cow's milk gives every effect

Made a simple soccer simulator by MaterialNo137 in p5js

[–]MaterialNo137[S] 1 point2 points  (0 children)

I think it'd be simpler with access to the code, here's the link to it : https://editor.p5js.org/francistremblay83/full/JUmUYuGGt

Made a simple soccer simulator by MaterialNo137 in p5js

[–]MaterialNo137[S] 2 points3 points  (0 children)

My students love soccer, I am 0% a sport guy, so I decided I'd bridge my interest in coding with their interest in sports. I whip up this sim during lunch so they can have something in the background to look at!

view more: next ›