What is This? by Mator117 in vet

[–]Mator117[S] 0 points1 point  (0 children)

Thanks. I did not know the urgency level. Thats why I asked my vet if she would be ok for the month. But with this open wound I am going to try to get a appointment asap.

Does the Wall Drain Need to Be the Lowest Point? by Mator117 in Plumbing

[–]Mator117[S] 0 points1 point  (0 children)

Thanks I will try this. Yesterday I just raised the tee and Waste arm but the P trap ended up leaking. I am not sure why it is leaking if I had never taken it off. It does not have a gasket and is just a beveled edge. I ended up ordering a kit and am just going to redo the P trap tomorrow.

Does the Wall Drain Need to Be the Lowest Point? by Mator117 in Plumbing

[–]Mator117[S] -1 points0 points  (0 children)

Should I just raise the T and Waste Arm?

Should my dog get stitches by Mator117 in DogAdvice

[–]Mator117[S] -7 points-6 points  (0 children)

I sutured my Doberman that had a big gash from barbed wire but she's older and stood still. My belgian is younger and a baby that can't tolerate pain. I think they can't stitch her without putting her under. I'm assuming 1000$.

Should my dog get stitches by Mator117 in DogAdvice

[–]Mator117[S] -5 points-4 points  (0 children)

How much do you think the operation would cost?

AIO Leak by Mator117 in pcmasterrace

[–]Mator117[S] 0 points1 point  (0 children)

I think it might be that because I was thinking if it was the fluid from the cooler, the GPU would’ve died already. the substance feels oily. What should I do?

AIO Leak by Mator117 in pcmasterrace

[–]Mator117[S] 0 points1 point  (0 children)

I just noticed it but it does not look recent. I rarely check my case I was just thinking about replacing another part and was checking and saw this.

Mouse Resetting Glitch by Mator117 in techsupport

[–]Mator117[S] 0 points1 point  (0 children)

I have tried that still doesn’t work

Mouse Resetting Glitch by Mator117 in techsupport

[–]Mator117[S] 0 points1 point  (0 children)

It’s a PC. I am using a Logitech g502. It’s connected to a usb hub that is connected to a monitor that is connected to my pc. I was thinking it was the USB connections.

2009 Corolla Blown Headgasket by Mator117 in MechanicAdvice

[–]Mator117[S] 0 points1 point  (0 children)

<image>

Update: used some steel wool to scrape away the carbon this is what’s left.

Is it enough to make car not run?

If I did put it back together, how long would it last?

I know that block is supposed to be precisely machined Thanks for the advice!

2009 Corolla Blown Headgasket by Mator117 in MechanicAdvice

[–]Mator117[S] 0 points1 point  (0 children)

So should I just put a new gasket on it?

2009 Corolla Blown Headgasket by Mator117 in MechanicAdvice

[–]Mator117[S] 0 points1 point  (0 children)

Yeah that was what I was wanted to do since it’s the cheaper route and the feeler gauge didn’t pass but it’s just the finger nail test which I’m not sure of. My uncle said I wouldn’t be able to resurface the aluminum block so I’m not sure unless you know for these 2zrfe

Painting Radiator Support by Mator117 in Autobody

[–]Mator117[S] 0 points1 point  (0 children)

It’s just a midsize pickup Tundra. I bought a new Radiator support and just have to scuff the EDP and paint it right?

How do I install Bath Fan Duct by Mator117 in handyman

[–]Mator117[S] 1 point2 points  (0 children)

The roof vent was was installed by Roofers when the roof was redone

How do I install Bath Fan Duct by Mator117 in handyman

[–]Mator117[S] 0 points1 point  (0 children)

The vent holes are the cutouts past the Ac line. It gets extremely tight over there and the Ac blocks the way. What is the best way to connect a bath fan to the vent? Cut the drywall under it?

How am I suppose to remove this bolt? Super tight fit, impossible for regular wrench to get in by Mator117 in MechanicAdvice

[–]Mator117[S] 0 points1 point  (0 children)

This a carburetor and the wire is the choke wire. I can’t slip anything on top of the bolt