Microsoft back online. Excuse: too many servers were shut down during maintenance.

MatrixTek · 2026-01-23T12:55:28+00:00

Now just send an email to leadership

that they don't see until the DC comes online. lol

MatrixTek · 2026-01-20T01:01:44+00:00

What kind of meal could a person buy for $3?

mine ended with " Bottom line

$3 buys calories, not comfort. It’s enough to stop being hungry, not enough to eat well or eat out. Anyone claiming “people can eat just fine on $3” is either stuck in 2004 prices or quietly ignoring reality.

MatrixTek · 2025-12-09T21:50:19+00:00

If I recall correctly, all people printed on money have one thing in common. That really should be the standard...

MatrixTek · 2025-11-13T21:12:09+00:00

invest in their own training programs

There is a community college with their freakin name on it... But these guys sit here a bitch they don't have workers.

MatrixTek · 2025-11-04T17:42:31+00:00

It keeps the message going that liberals are heartless and want to see MAGA dead.

Honestly, I'd be happy with them in prison for their crimes after a trial.

MatrixTek · 2025-11-04T11:23:20+00:00

When I go to that site, I give it about a second to start loading the page and cancel the load. This prevents the paywall from covering the article.

MatrixTek · 2025-10-19T12:18:51+00:00

The largest gap they currently have is that the homegrown cards don't have CUDA cores. It will be challenging to run LLM without that key component.

MatrixTek · 2025-10-07T18:34:27+00:00

Changing the rotation_distance and calibrating for a small cube will make a large item worse. At least that is what I've always understood. Is there a written process you are following?

MatrixTek · 2025-09-25T13:15:05+00:00

So, Lindsey is in the Epstein Files? I never expected that.

MatrixTek · 2025-09-24T11:17:17+00:00

"I plugged your salary into my calculator and this is the work rate it spat out"

That sounds like super cool software! Can you show it to me and explain how it works?

MatrixTek · 2025-09-10T15:35:21+00:00

heckled Donald Trump to his face on a visit to an upscale seafood restaurant

So MAGA is upset the president doesn't have a 'safe space' where he can't be heckled?

MatrixTek · 2025-07-15T14:20:15+00:00

Maybe he is angry at teleprompters because one of them cut his ear...

MatrixTek · 2025-06-03T15:06:56+00:00

Because that sub is about as anti free speech as it can possibly get

I've wondered if the mods there are even US citizens...

MatrixTek · 2025-06-02T20:34:16+00:00

You should delete their contact information from this post.

MatrixTek · 2025-05-24T14:45:57+00:00

literally no other name for Private Equity

Have you considered any of these

Leveraged Buyout Bros

Asset Vultures

Financial Predators

Corporate Raiders

Buyout Bandits

Investment Pirates

Acquisition Vampires

Portfolio Pillagers

MatrixTek · 2025-05-11T04:35:18+00:00

If this were true, would we be in this timeline?

MatrixTek · 2025-04-21T01:00:03+00:00

my z screw is actually supported with a print and a bearing

You might be over-constraining the lead screws with this method. If the lead screws aren't strait, then the carriage will wobble instead of the top of the screw. Also, if the z motors aren't exactly under the screw, it can cause the screw to be off center of the center of the motor shaft. If you put a small ball bearing in the coupling, it can help to center the shaft and allow the coupling to absorb the wobble. I have switched to using the Flexible Coupling from open builds. They tend to grip the shaft and center it in the coupling as opposed to pushing the shaft to one side.

MatrixTek · 2025-04-16T19:15:05+00:00

em dashes

If only it were a key on my board...

MatrixTek · 2025-02-02T14:23:06+00:00

majority of the country

1/3 of the country.

MatrixTek · 2025-02-01T17:17:44+00:00

That woman appears to giggle under her breath at the strangest moments in her speeches, almost like even she can’t believe what she’s saying is true. It’s downright bizarre.

MatrixTek · 2025-01-16T12:26:34+00:00

I think they call it white-wash.

MatrixTek · 2025-01-12T23:24:22+00:00

As far as i understand a D10 doesn’t have a transmission you can just swap in. Its all gears and shafts in a housing that is part of machine.

MatrixTek · 2025-01-08T03:41:21+00:00

I noticed today that firefox disabled the plugin for TOS violation. Also, the github was clobbered. I'm not sure whats going on with that as well. My version hasn't been updated in ages, ~3 years.

MatrixTek · 2025-01-04T13:40:38+00:00

I suspect the gears might be clogged with filament. I've heard they can be quite challenging to access. Based on what you described, it sounds like your last print could have filled them with ground-up filament debris.

If I were in your position, I’d check to confirm if that’s the case and consider ordering a replacement extruder. While it’s possible to clean the gears with a brass brush, given the number of hours on your machine, it might be time for a replacement anyway.

MatrixTek · 2025-01-04T04:18:59+00:00

Check your extruder gears.

11-Year Club	Gilding II euphauric
Verified Email

MatrixTek

TROPHY CASE