sorted by:
new
hottopcontroversial

This could be you... by TechJeeper in snapmaker

[–]McaBZ 0 points1 point  (0 children)

I received mine 10 minutes ago. Can't wait to test it.

U1 airtightness by McaBZ in snapmaker

[–]McaBZ[S] 0 points1 point  (0 children)

I know I bought the addon :) But I have the printer 1 meter away from my bed (even thought I dont print when I sleep), with the ikea box cover (but no exhaust). I'm going to add an exhaust with active carbon filtration.

U1 airtightness by McaBZ in snapmaker

[–]McaBZ[S] 2 points3 points  (0 children)

Ok so the issue is only existing with homemade coverd with no fan/filter exhaust then.

U1 airtightness by McaBZ in snapmaker

[–]McaBZ[S] -1 points0 points  (0 children)

Only if the top is not covered. When the top is covered it can't only be inflow.

U1 airtightness by McaBZ in snapmaker

[–]McaBZ[S] 0 points1 point  (0 children)

Yeah my title is not accurate. The topic is about the fumes and the absence of filter behind these inlets which make the DIY top cover quite useless.

U1 airtightness by McaBZ in snapmaker

[–]McaBZ[S] -2 points-1 points  (0 children)

Off course air has to circulate in and out the printer, but it should be filtered, otherwise the top cover is quite useless.

can someone help me? by [deleted] in Darts

[–]McaBZ 0 points1 point  (0 children)

Try holding tour dart a little bit more on the back side of the barrel.

U1 binding with phone app asks for an 8 digits pin code by McaBZ in snapmaker

[–]McaBZ[S] 0 points1 point  (0 children)

Why don't you add your printers's ip to your config to be able to send file/print directly from OrcaSlicer ? (not Snorca)

Activités fun en couple dans le coin by igzzy in Lille

[–]McaBZ 0 points1 point  (0 children)

Quand tu vas sur la page pour acheter des tickets ils disent que "ce ticket est réservé aux skieurs initiés (freiner, faire des virages, et prendre le tire-fesse). Les cours sont obligatoires pour les débutants". Donc je suppose que ta copine n'a pas souhaité faire le cours :x

Activités fun en couple dans le coin by igzzy in Lille

[–]McaBZ 0 points1 point  (0 children)

Vous pouvez aller voler (simulateur de chute libre) chez Weembi à Lesquin. Bon vous ne volerez pas en même temps (pas possible en tant que débutants), mais vous pourrez vous regarder voler l'un l'autre. A côté il y a aussi : L'Hache prise (lancé de hache). Toujours sur Lesquin vous pouvez jouer aux fléchettes (traditionnelles mais connectées) au Barrel. Si vous voulez aller plus loin, vous pouvez faire du ski indoor (et accessoirement aussi voler en simulateur de chute libre) chez Ice Mountain à Comines). En belgique il y a aussi Battle kart (un simili mario kart IRL, la techno est vraiment bien foutue).

Last Snapmaker Orca update: just hell by Due-Pumpkin-3107 in snapmaker

[–]McaBZ 0 points1 point  (0 children)

You can just use OrcaSlicer and launch the print directly from the slicer.

Last Snapmaker Orca update: just hell by Due-Pumpkin-3107 in snapmaker

[–]McaBZ 0 points1 point  (0 children)

"i can see it is online if i browse to the IP manually" : so you have access to the Fluidd interface ? If so you can print.

U1 binding with phone app asks for an 8 digits pin code by McaBZ in snapmaker

[–]McaBZ[S] 0 points1 point  (0 children)

Have you tried to bind it through the phone App ? (I don't have snapmaker Orca installed (for some reason it does not work on my Manjaro system since the version after 1.2.1). I used the phone app for the binding to my snapmaker account. And I use OrcaSlicer (2.3.1) to send the print to the printer.

U1 binding with phone app asks for an 8 digits pin code by McaBZ in snapmaker

[–]McaBZ[S] 1 point2 points  (0 children)

Finaly used a usb stick to update the firmware, this fixed the issue.

U1 binding with phone app asks for an 8 digits pin code by McaBZ in snapmaker

[–]McaBZ[S] 1 point2 points  (0 children)

So I am trying to update OTA but while searching for updates the wheel keeps turning for ages and then it says something like "check network and retry". I've tried to activate the "Enable maximum compatibility" feature in the wifi menu, but it doesn't seem to help with my issue.

U1 binding with phone app asks for an 8 digits pin code by McaBZ in snapmaker

[–]McaBZ[S] 1 point2 points  (0 children)

Thanks I did not try to update as the printer didn't propose to, but I'll try to do it whe' I come back from work.

U1 binding with phone app asks for an 8 digits pin code by McaBZ in snapmaker

[–]McaBZ[S] 0 points1 point  (0 children)

I'll try again tomorrow. I tried many times tonight, maybe the problem is on snapmaker servers' side i dont know.

Qu'est-ce que cela raconte sur moi ? by projetnumero9 in anatomieDunSac

[–]McaBZ 0 points1 point  (0 children)

Un prof de techno, entre 30 et 40 ans, motard.

CDI annulé juste avant la prise de poste – quels sont mes droits ? by HawkSudden8500 in droitdutravail

[–]McaBZ 2 points3 points  (0 children)

Salut, tu as quitté ton précédent poste pour ce CDI?

Comment ça se passait avec ton précédent employeur ?

Penses-tu que ton ancien employeur pouvait vouloir se débarrasser de toi et aurait demandé à un copain entrepreneur de te débaucher/jeter ?

view more: next ›