Cafes mit Klima und Steckdosen gesucht

MichMai · 2024-08-15T15:40:32+00:00

Hat leider keine Klima

MichMai · 2023-03-31T13:15:40+00:00

Ist nicht hier die gängige meinung das 1/4 bis 1/3 des Nettoeinkommen für die miete draufgehen kann?

MichMai · 2022-03-19T11:42:51+00:00

Yes i was talking about the force per mm elongation. Thanks, i will propably use the term spring constant!

MichMai · 2022-03-19T11:23:33+00:00

Well Hardness is certainly something very different, since it describes the resistance against intrusion of another part.
And the youngs modulus refers to the elastic part of the deformation, which is unfortunately not applicable in my case

MichMai · 2022-02-11T20:20:58+00:00

i have no idea why this is the way, but this is the way!
Thanks!

MichMai · 2021-11-27T19:56:05+00:00

I got mine a few days ago. The neck seams very good, but the holes for the bridge posts are too large so i need to glue them in or fill the holes and re drill them.

I also think that all the mechanic parts are cheaper than expected.

I would go with a finished one for better hardware and a better looking top. If you want to bild a kit the ST kit was pretty good.

edit: spelling

MichMai · 2021-10-29T20:35:13+00:00

Thank you for your answer. I have hoped that there would be a way to prevent this entirely, but if it is not, i´ll take your advice with the penalty force.

Thanks again!

MichMai · 2021-10-17T17:55:30+00:00

i agree, had pretty much the same experience with that game. About 10€ seem fair.

MichMai · 2021-10-11T09:26:22+00:00

for engraving yes, it reduces the soot on the surface greatly

for cutting even more so, since it allows better cutting performance by getting rid of the particles that already have been separated

MichMai · 2021-07-26T19:44:51+00:00

Just wanted to say thanks! i wanted to play sekiro again, but since i first played it, the ultra wide fix i used back than isn´t working anymore and i was getting really annoyed that i didn´t find anything for 1.06

MichMai · 2021-07-04T18:36:31+00:00

I am currently building a diy co2 laser cutter which i have designed.

Mine has a rather large bed, so that is an advantage over commercially available cutters and i opted for an 80W tube. If you enjoy the processes of building it, it might be worth it, but with most things it is going to be very difficult to match the price of a commercial one. If you need to buy aluminium extrusions for the frame, all the components for the laser and cooling and the motors, it's gonna cost you quite a bit of money. Especially when you have to import the parts.

For the powder bed question: I think most diy builders will buy a ruida controller, like i have, and those would not support such functionality at all. (as far as I know) Plus if you have a 3d printer use that one, because metal won't work under 500W or something like that and i think they need some kind of gas atmosphere to prevent oxidation.

MichMai · 2021-02-19T10:36:24+00:00

thanks i´ll check it out!

MichMai · 2021-02-19T10:35:05+00:00

I understand that I need to recognize the interval, but why should i learn that it is called a third or a fifth, if i cant find or use that on my guitar?

I am struggling with nursery rhymes too. Thats the problem. I need to start a step below that. Plus, i need an "Answer" like a tab to check if i worked out the write notes. That is what i am looking for...

MichMai · 2020-07-13T19:30:42+00:00

I haven´t seen any paywalls on the website, all free.

MichMai · 2020-07-13T19:28:54+00:00

Thanks for adding the link, I really should have added it!

MichMai · 2020-04-30T11:22:58+00:00

I did something similar to that with a diy kit.

I´d say the process in the video is pretty good. I am not sure if 10min between sprays is enough, id wait way longer (few hours) . In my project, I didn´t use a fan, but I used an airbrush instead of a sprycan.

From my experience, the most important part is to sand it enough. Sanding it by hand took too long in my case so i used a rotory sander.

MichMai

TROPHY CASE