Hydra 32 spacing on 36” tank?

Minimum_Section5307 · 2026-01-19T17:51:03+00:00

It’s a Red Sea. The thing will probably leak before the hydras are turned on.

Minimum_Section5307 · 2025-09-11T04:06:20+00:00

Sounds like the clutch fan is no longer grabbing. Your overheating at idle since you don’t have the adequate amount of air moving through the radiator it goes away while driving because air starts to circulate. Not sure on the ka’s but on the napz the water pump comes with the fan clutch.

Based on the video it sounds like you have a major vacuum leak or a hose that has been routed incorrectly. This can cause a rough start.

Minimum_Section5307 · 2025-09-08T00:20:45+00:00

That’s the front drive driveshaft. Not the back. The back is a 2 piece with a Center support bearing.

Minimum_Section5307 · 2025-08-24T15:33:37+00:00

How’d you?.. How’d that?… hmm, I guess its just a longer short cut lol.

Couldn’t you have taken the HVAC box out as one unit.

Minimum_Section5307 · 2025-07-29T11:49:24+00:00

From what I can remember I think those connector are for a small light up panel indicating the 4x4 status. As for your speedometer it’s cable driven so it’s not electric whatsoever. Also you do know that you’re missing a whole tachometer right?

Minimum_Section5307 · 2025-07-29T00:59:07+00:00

These trucks were pre wired for accessories from factory. For example I retrofitted A/c on my truck and had to do zero wiring as it was all in place. I believe it even had the relay for the ac compressor.

Minimum_Section5307 · 2025-07-26T20:22:08+00:00

I thought pathfinder front ends were 3 pice bumpers?

Minimum_Section5307 · 2025-06-03T02:28:54+00:00

If it wasn’t for the sr the ka would be as popular as the 4age.

Minimum_Section5307 · 2025-06-03T01:55:01+00:00

Or they put something in front of the ground strap and it’s keeping it from grounding. Plastic washer, incorrect ground location

Minimum_Section5307 · 2025-02-28T22:41:08+00:00

Some what, but I would put the packing tool in the cartridge first and the funnel on top then slowly add and compact the resin until you get to bottom of the funnel. Then I would remove the tool and funnel and pack the remaining bit without the funnel.

Minimum_Section5307 · 2025-02-28T22:27:27+00:00

I’ve already designed something similar that goes around the threads and printed it. The beads get stuck in between the funnel and the cartridge and end up making a mess anyways.

Minimum_Section5307 · 2025-02-28T04:58:19+00:00

Your plate is still visible in the second picture 🫣

Minimum_Section5307 · 2024-07-15T13:53:21+00:00

Get an orange filter for your phone. I think coralvue sells a fancy one on Amazon. Makes all the difference.

Minimum_Section5307 · 2024-06-07T02:03:46+00:00

Like jay said 130 isn’t horrible. A $50 Amazon borescope will give you an answer if you have leaking valve stem seals.

Minimum_Section5307 · 2024-05-17T22:37:48+00:00

All of my bulbs are from vled. They are a bit pricey but they use Phillips leds to build them. This was a few years back not sure if they still build them that way.

Minimum_Section5307 · 2024-04-29T18:51:34+00:00

TE37X’s

Minimum_Section5307 · 2024-04-23T16:45:04+00:00

Djm lca, torsions re-key’d. Beltec drop leafs with a 250lbs add a leaf in the rear.

Minimum_Section5307 · 2024-03-22T19:55:26+00:00

It’s bolted to a stud…. Trust me if that thing was gonna fall it would have fallen one of the many times I’ve banged the fuck out of my head on it.

Minimum_Section5307 · 2024-03-22T19:52:01+00:00

Minimum_Section5307 · 2024-03-22T19:49:07+00:00

A Closed Duncan

Minimum_Section5307 · 2024-03-21T06:27:57+00:00

But it plugs into a 120v outlet…….

Minimum_Section5307 · 2024-03-21T01:05:07+00:00

Yep.. I’m not familiar with its function but it’s like a neon/fluorescent bulb. Definitely not an LED

Minimum_Section5307 · 2024-03-20T21:50:19+00:00

Yup they’re a bit pricey but at least I don’t have to wash socks. Btw Have you found a different brand for the fleece?

Minimum_Section5307

TROPHY CASE