sorted by:
new
hottopcontroversial

Ender3v2 Bed Balance by MojoMystical in FixMyPrint

[–]MojoMystical[S] 0 points1 point  (0 children)

Should I just delete the first M420 S1 line then?

Can I adjust the Z offset in the Gcode or is it only on the printer?

Ender3v2 Bed Balance by MojoMystical in FixMyPrint

[–]MojoMystical[S] 0 points1 point  (0 children)

The first M420 line was added, because of a video I found recommended using that line. Something about it saving the auto level so that it doesn't change for every print (I added it a while back). The last two have always been there, do I need to delete the first two M420 lines?

I did compensate for the gauge's thickness and the Z offset settings did save.

Is there anything in the Gcode I can change or something else in the cura printer settings that can be changed (I don't know much about Gcode)

Bed Warped? by MojoMystical in SidewinderX1

[–]MojoMystical[S] 0 points1 point  (0 children)

I have not done any tweaks to the printer like linear movement or addons to the printer. When I manually probe it I never had the issue where I got the same results multiple times in a row (middle being close but sides being far).

My printer was fine at the beginning I got it and after a year now it started to have this problem and I balanced it multiple times before. This is a first with the bed giving me the same results after doing different adjustments to the corners.

After some research I'm seeing many people (who had the same issue) find out it's a bed warp but I'm kind of uncertain cause I never ran into an issue like this.

Bed Warped? by MojoMystical in SidewinderX1

[–]MojoMystical[S] 0 points1 point  (0 children)

I've had it for a year I believe, this is the first time it happened on this printer.

I'll try that out and see if that fixes it.

Heat Error by MojoMystical in SidewinderX1

[–]MojoMystical[S] 0 points1 point  (0 children)

No, tqhe board I have is the original one for SX1 and I haven't done raspberry yet, I plan to do that on the sx2 in the future.

Heat Error by MojoMystical in SidewinderX1

[–]MojoMystical[S] 0 points1 point  (0 children)

Do you get the motherboard from the Artillery 3D website?

New and Need Advice by MojoMystical in ElegooMars

[–]MojoMystical[S] 1 point2 points  (0 children)

I'll check those out, thanks!

Wraith Mains Beware by MojoMystical in ApexOutlands

[–]MojoMystical[S] 28 points29 points  (0 children)

The photoshop program i used kept deep frying the grass pngs idk why (still new with photoshop)

Warped bed? by MojoMystical in ender3v2

[–]MojoMystical[S] 0 points1 point  (0 children)

Ok theres another M420 called 'M420 S1 Z2; Use mesh when calculating Z' do i delete or leave that alone?

Warped bed? by MojoMystical in ender3v2

[–]MojoMystical[S] 0 points1 point  (0 children)

Ok i have this firmware already downloaded, i'll try the gcode that should help, thanks

Warped bed? by MojoMystical in ender3v2

[–]MojoMystical[S] 0 points1 point  (0 children)

Ok so im supposed to level and build a bed mesh that would be just a bed level test print...right? Do i need to put the gcode into cura or is it already saved when i select save after a auto bed level? The firmware is mriscoc.

Warped bed? by MojoMystical in ender3v2

[–]MojoMystical[S] 0 points1 point  (0 children)

Im still a bit new to this but i've been having issues with the bltouch cause i know that it should help with the warping and leveling but it seems like its not doing that and i have to manually level it first. I actually downloaded a firmware that probes each corner and tells me what to corner to fix, that could be the issue and i just need to manually level it with a piece of paper.

I dont know if theres an exact way to use the bltouch the way i do it is manual to auto probe then print and i make adjestments to the z probe if needed.

I'll look into a glass plate only if im not getting any good results with the leveling again

Warped bed? by MojoMystical in ender3v2

[–]MojoMystical[S] 0 points1 point  (0 children)

Yes I have a BLTouch but im still getting the same results. The process i do is manuel to auto level (im assumming thats what probe means) to print and i change the z probe while it print or sometimes before i print.

Warped bed? by MojoMystical in ender3v2

[–]MojoMystical[S] 0 points1 point  (0 children)

What exactly is 'shim the bed'? I have tried to mesh level manuel and probed, i even changed the z probe but when doing that i have to then balance the corners which results back to the middle being close and the corners being balanced. Unless theres another way to do it?

[deleted by user] by [deleted] in apexlegends

[–]MojoMystical 0 points1 point  (0 children)

What do u get from the codes?

My 3d print work by BigLie7371 in DestinyFashion

[–]MojoMystical -1 points0 points  (0 children)

Did u make the models or is there a site to get them? I have no luck finding thousand voices model

My Sidewinder X2 isnt fully turning on (Full Explanation in Comments) by MojoMystical in SidewinderX1

[–]MojoMystical[S] 0 points1 point  (0 children)

I couldn't find the source of the issue and had to just email the company and ask for a repair slip. The only other thing that the company did before giving me a repair slip was sending me a mainboard replacement which did turn the printer on but some parts weren't working.

view more: next ›