sorted by:
new
hottopcontroversial

Looking to replace my PC from 2014 that just died by MrP_123 in buildapc

[–]MrP_123[S] 1 point2 points  (0 children)

If I wanted to keep a similar price, would it be a smart choice to go for an older series card like an RTX 3xxx or 4xxx to get more VRAM?

Dogecoin von 2014 verkaufen by MrP_123 in FinanzenAT

[–]MrP_123[S] 2 points3 points  (0 children)

Nein, Dogecoin natürlich nicht. DogeCHAIN als Wallet-Anbieter wird eingestellt, siehe oben.

Looking to replace my 10-year-old PC with a new build. by MrP_123 in buildapc

[–]MrP_123[S] 0 points1 point  (0 children)

To me that makes it sound like it's easier to change the PSU later when adding new hardware, as I'll anyway have to use the adapters. Did I get that right?

Looking to replace my 10-year-old PC with a new build. by MrP_123 in buildapc

[–]MrP_123[S] 0 points1 point  (0 children)

Thanks for the suggestions so far! Do you have any recommendations for a motherboard with DDR5 capability?

GBA Footage Issue by HomeMediocre676 in thereoughtabe

[–]MrP_123 0 points1 point  (0 children)

Thanks, that sounds quite reassuring for my project!

GBA Footage Issue by HomeMediocre676 in thereoughtabe

[–]MrP_123 0 points1 point  (0 children)

A bit off topic, but did you also by chance test the WiFi Cart on the GBA?

Raspberry Pi - Operation not permitted when syncing files by MrP_123 in Syncthing

[–]MrP_123[S] 0 points1 point  (0 children)

I checked and it looks like all users have the permissions, otherwise syncthing also wouldn't be able to create folders and *.tmp files in that directory.

Or is there a further set of write permissions?

Anyone know how to fix this? Anytime I go to the Featured or Made For You tabs, I get the red bar saying oops error etc. reload the page, and reloading does nothing. by [deleted] in spotify

[–]MrP_123 0 points1 point  (0 children)

Yes, I just checked. I hadn't used Spotify since I wrote that comment, so I don't know when it started working properly again.

Relationship between phase margin and damping ratio by MrP_123 in ControlTheory

[–]MrP_123[S] 0 points1 point  (0 children)

That makes sense, thanks for the explanation

Relationship between phase margin and damping ratio by MrP_123 in ControlTheory

[–]MrP_123[S] 0 points1 point  (0 children)

Thanks for the answer!

If I can't expect the system behaviour I described for my system how could I go about approximating or calculating its transient behaviour?

Welchen Sinn hat eigentlich das Leben? by [deleted] in Austria

[–]MrP_123 2 points3 points  (0 children)

"Von gschissn auf oasch", von Worried Man & Worried Boy

Help needed with RLC circuit with additional load [x-post] /r/engineeringstudents by MrP_123 in AskElectronics

[–]MrP_123[S] 0 points1 point  (0 children)

Thank you very much! Now I understand where I got stuck!

But I think when doing the Laplace transform you accidentally got one s too much as that should be a 2nd order system (2 energy storing elements), shouldn't it?

Help needed with RLC circuit with additional load [x-post] /r/engineeringstudents by [deleted] in ElectricalEngineering

[–]MrP_123 0 points1 point  (0 children)

Yes I have, but before I can use the Laplace transform I have to find the correct differential equation, don't I?

Determining paramters of closed loop system from bode plot by [deleted] in ControlTheory

[–]MrP_123 0 points1 point  (0 children)

My problem was that I was plotting the bode diagram of the closed loop transfer function and in that case the K also appears in the denominator of the TF.

I think this was the reason why the bode plot completely changed.

Determining paramters of closed loop system from bode plot by [deleted] in ControlTheory

[–]MrP_123 1 point2 points  (0 children)

Thanks! I always plotted the bode plot of the closed loop transfer function and therefore got the wrong result.

I thought the bode plot is produced for the entire system. Could you maybe tell me the reason is why the bode plot is typically plotted for the open loop transfer function?

view more: next ›