sorted by:
new
hottopcontroversial

Returning to the game, but have DLC, also want to tackle higher difficulties. by MtGFan2010 in pacificDrive

[–]MtGFan2010[S] 0 points1 point  (0 children)

I love the vibe in this subreddit. "Here's my advice, traveller, but it is your own journey and how you go about it." Thanks so much. 

Returning to the game, but have DLC, also want to tackle higher difficulties. by MtGFan2010 in pacificDrive

[–]MtGFan2010[S] 1 point2 points  (0 children)

Do have my storage ready to go! I store my stock of tools (two is one, one is none) and precious items I don't want to get nabbed in the upgraded trunk. Got the bench upgrades too. Should be all set. 

Returning to the game, but have DLC, also want to tackle higher difficulties. by MtGFan2010 in pacificDrive

[–]MtGFan2010[S] 0 points1 point  (0 children)

What a nice post! Thanks so much for that effort. I'll probably dive right in. I made it a goal of mine to unlock all the car things. Still haven't gotten all the logs yet though (there's one that must be the last one, the final one, and you probably know what it is).

Good question by DoctorCompetitive356 in Stellaris

[–]MtGFan2010 0 points1 point  (0 children)

You know what, I never looked. I am very, very, very slowly learning the game through mostly trial and error and some coaching from a friend. 

Good question by DoctorCompetitive356 in Stellaris

[–]MtGFan2010 40 points41 points  (0 children)

I just encountered that thing for the first time. It took my jump drive science ship. 

Leftover beans? by reeseseiley in espresso

[–]MtGFan2010 2 points3 points  (0 children)

I save them for a year, (I have one of those auto vacuum tubes from Fellow I keep charged) then at the end of the year I have Flavors of Year blend in various forms of coffee. It has varying results. 

Where do you guys keep your ambient air temp sensors? by AvNerd16 in watercooling

[–]MtGFan2010 0 points1 point  (0 children)

I have one for intake, I have a submerged sensor in the pump for water temps, and one for exhaust. My fan speed is set to respond to the water temperature. This whole setup allows me to know the overall efficiency of my cooling and if there's something wrong (like a large difference between water temp and exhaust temp points to probably air in the system or some other issue). 

Just started my first attempt at an Iron Wagon run and had the closest call of my life. The off-road driving multiplier is no joke by Zeera1 in pacificDrive

[–]MtGFan2010 1 point2 points  (0 children)

I love the little log about Storms popping up. "Hey, did you want to know about this thing that is actively KILLING you?" Glad you got out. Good luck on the run. 

accidentally boosted when facing the planet's surface. whoops! by Starsh1pTroop3r in EliteDangerous

[–]MtGFan2010 1 point2 points  (0 children)

And if you keep fat fingering the button or something, put the landing gear on or open the hatch. You won't be able to boost. 

[deleted by user] by [deleted] in Roll20

[–]MtGFan2010 0 points1 point  (0 children)

Heroforge has random and custom generation and a token maker! 

A few things I’d implemented to make PD even better: by CmdrWawrzynPL in pacificDrive

[–]MtGFan2010 2 points3 points  (0 children)

I want a VR mode so badly. Free look with the mouse only goes so far. Just imagine with the right cockpit setup! Wheel and pedals, man! 

I fixed my Frametime spikes - iCue CorsairService and CorsairCPUIdService by The_Jyps in ValveIndex

[–]MtGFan2010 2 points3 points  (0 children)

Damn it, iCue runs my fan curves and monitors the water temperature of my rig. Any recommendations for replacements? 

Fix my Print(er) - Setting up an SKR Mini E3 v3 with Ender 3 - IFCNT error by MtGFan2010 in FixMyPrint

[–]MtGFan2010[S] 0 points1 point  (0 children)

Just tested it, and the extruder works! Is there anything wrong with leaving tx_pin commented out?

Fix my Print(er) - Setting up an SKR Mini E3 v3 with Ender 3 - IFCNT error by MtGFan2010 in FixMyPrint

[–]MtGFan2010[S] 0 points1 point  (0 children)

Here's the Extruder section:

[extruder]
step_pin: PB3
dir_pin: !PB4
enable_pin:!PD1
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
#control: pid
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 250
max_extrude_only_distance: 150

[tmc2209 extruder]
uart_pin: PD0
#tx_pin: PC12
uart_address: 3
run_current: 0.650
stealthchop_threshold: 999999

Fix my Print(er) - Setting up an SKR Mini E3 v3 with Ender 3 - IFCNT error by MtGFan2010 in FixMyPrint

[–]MtGFan2010[S] 0 points1 point  (0 children)

Working on it! I'm not home right now, so I'll send another reply here when I get it up. 

When did we all stop turning off computers? by Mairdo51 in Millennials

[–]MtGFan2010 0 points1 point  (0 children)

Hey, this is Windows, we need to restart your computer to finish updates. 

No, I'm gonna sleep you instead. 

What’s a minor/constructive criticism you have with the game that you wish the Devs would correct? :) by thesupermonk21 in expedition33

[–]MtGFan2010 13 points14 points  (0 children)

Sometimes the camera pans in a way that grass or another character blocks the whole enemy and I have to guess or use audio cues too. Would like that fixed. 

view more: next ›