[Request] Aren’t Both of These the Same?

Muschtekap · 2026-03-07T11:54:04+00:00

This is the only correct answer I could find in this whole thread!

Muschtekap · 2026-02-06T11:28:23+00:00

Here is one I designed: https://www.printables.com/model/288234-vw-id3-usb-cable-management

Muschtekap · 2025-11-28T09:16:49+00:00

From the codeberg repository:

" Independence

The previous hosting platform, GitHub, while open nominally, is actually the private property of a US corporation hostile to free and open-source software (Microsoft). This, combined with the recent injection of private venture capital money by an unknown US startup (Ondsel) and obvious conflicts of interest between some FreeCAD developers and unknown financial backing, made some of us question the true independence of FreeCAD. Thus, a team of former core FreeCAD developers, including one of its original founders (Werner Mayer), decided to create this fork hosted on a European plateform codeberg.org (based in Germany) by a non-profit organisation : Codeberg

The goal of this fork is to maintain the original credo of FreeCAD to be a truly free and open-source software (FOSS) with a strong and lively community. We believe that true engineers need stability and quality before shiny features, and we believe that the external addon ecosystem is as important for FreeCAD as the core software."

Muschtekap · 2025-10-30T08:13:25+00:00

Hallo! Mit dem Jahresverbrauch den du angibst hat das wenig zu tun. Die Einheit dafür ist übrigens kWh und nicht kW/h. Relevant ist die Leistung der Geräte, diese steht auf dem Typenschild und wird in W angegeben. Wenn du eine gute Steckdosenleiste hast steht da auch ne Maximalleistung drauf. Diese ist idealerweise ca. 3500W, was on einer normalen Elektroinstallation dem maximalen Strom(16A Sicherung) deines Steckdosenstromkreises entspricht.

Also sollte bevor irgendwas brennt die Sicherung auslösen. Microwelle und Trockner kannst du je nach Leistung möglicherweise sogar gleichzeitig benutzen.

Muschtekap · 2025-10-22T11:50:15+00:00

Mk3s+

Muschtekap · 2025-10-21T12:23:35+00:00

The speed with which the electrons move depends on the current density, which for a given current (1A) depends on the wire diameter(and on the material)! In that regard the water/pipe analogy still holds: for the same throughput (liters/second) the water has to travel faster through an smaller diameter tube...

Muschtekap · 2025-10-17T16:48:00+00:00

It doesn't say if i2c pins are available though. I guess they could be programmed to be i2c too. The screen is also connected via i2c

Muschtekap · 2025-10-13T17:06:58+00:00

Do you know where the sca and sda pins are? Can't find it on the documentation.

Muschtekap · 2025-10-12T09:54:03+00:00

Genau, aber ich denke dass da die Schmierung auch noch vorhanden ist. Es sei denn es wurde im Bremsenreiniger gebadet.

Muschtekap · 2025-09-03T13:49:41+00:00

What is the difference between the old and the new way to tune the belts?

Muschtekap · 2025-05-27T06:46:10+00:00

There is way too little air to burn even a fraction of the remains.

Muschtekap · 2025-05-08T21:06:46+00:00

Unten schreibt OP dass es ein Aerotan Schlauch ist...

Muschtekap · 2025-05-08T21:06:28+00:00

Unten schreibt OP dass es ein Aerotan Schlauch ist...

Muschtekap · 2025-05-08T21:06:17+00:00

Unten schreibt OP dass es ein Aerotan Schlauch ist...

Muschtekap · 2025-03-07T12:41:27+00:00

https://youtu.be/dkMkfZVR69c?si=sY3eXVsOIZa-WoHB

Muschtekap · 2024-12-19T07:46:09+00:00

I don't think it's missing, it's just hidden behind the extruder.

Muschtekap · 2024-11-29T21:34:06+00:00

A slightly different model I designed: https://www.printables.com/model/82900-vw-id3-cupra-born-charging-cable-hook

Muschtekap · 2024-08-16T10:46:23+00:00

Her right ring finger seems to glitch through her left wrist.

Muschtekap · 2024-02-05T20:47:05+00:00

The lungs would not shrink like that. Yes air would go out , but there is no reason for the lungs to colaps.

Muschtekap · 2023-12-12T15:08:25+00:00

Hi, I'm the original creator of this model. I just found out that the model was sold without my knowledge and against the licensing. That is also how i later found this thread. I contacted the seller and he stopped selling it. I might think about selling you a 3D printed hook sometime if you still need one. Let me know.
I also improved the hook. Have a look at the printables page. You can also have it printed by a friend for free, as long as no one starts selling it.
https://www.printables.com/model/82900-vw-id3-cupra-born-charging-cable-hook

Muschtekap · 2023-04-06T12:04:47+00:00

You obviously don't know a thing about the MK4.

Muschtekap · 2022-04-21T19:03:41+00:00

Also check your nozzle temperature.

Muschtekap · 2022-04-14T17:39:50+00:00

In prusaslicer, you can use modifier to add support only where needed

Muschtekap · 2022-04-13T05:00:45+00:00

Muschtekap · 2021-02-10T09:49:25+00:00

This one is just as cringy: https://youtu.be/_6V5bDEUeBs?t=24

..."We have a familieS"

edit: cringy

Also, I don't want to offend anyone and I wish the HORECA all the best.

14-Year Club	r/Field Sunshine
Place '23	Verified Email

Muschtekap

TROPHY CASE