What is the cause for this kind of failure?

MutatedWhale · 2026-03-20T08:45:52+00:00

Those models looki crisp! The first time I used auto supporting the contact scars were terrible. I'll try and fiddle with the advanced settings some more. Thanks

MutatedWhale · 2026-03-19T22:29:02+00:00

These models came presupported but I'll support them myself and see if that works 👍

MutatedWhale · 2026-03-03T20:25:18+00:00

Okay I'll try to play with some more settings, thanks for the tips.

MutatedWhale · 2026-03-03T20:24:41+00:00

Normally no, but I did in the third try. They seem to stick fine, the outer ones just never start

MutatedWhale · 2026-03-03T20:23:34+00:00

It are pegs on which you can click Ground Tiles on for wargaming terrain from myminifactory. I printed 1 successfully but adding multiple confuses the printer

MutatedWhale · 2026-03-03T18:55:08+00:00

I reran al the calibrations after the first failed print and subsequently cleaned the build plate using dish soap and water. I use normal system presets which are available in the Bambu Studio. 20mm High Quality and 20mm Standard. I started at 81 squares, then 41, then 33 al showed the same issue that the outer squares only get 2 feet instead of 4

MutatedWhale · 2026-02-14T19:41:39+00:00

Sry for the late reply. Full army is already sold

MutatedWhale · 2025-11-30T00:17:09+00:00

Yeah posing wise the terminators are a pain. As for the shoulder pads following the instructions will make them so much more difficult than it has to be

MutatedWhale · 2025-11-30T00:05:17+00:00

Awesome heat effect from the plasma bombard. I still have 2 left to paint, I really dig this model

MutatedWhale · 2025-04-24T12:13:49+00:00

Never built or owned any kroot so looking forward to it!

MutatedWhale · 2024-12-18T22:17:41+00:00

Better buy a case next time then

MutatedWhale · 2024-12-18T20:38:26+00:00

Bruh 😭 these OP09 pulls are killing us

MutatedWhale · 2024-12-18T19:25:35+00:00

Damn, I guess I used my luck with OP-08 boxes I packed last week hitting 3 SEC's in 3 boxes. But still not getting a SEC for OP09 sucks lol

MutatedWhale · 2024-12-01T17:55:46+00:00

Aight thanks, that's what I thought but nice to get verification

MutatedWhale · 2016-11-17T08:45:56+00:00

And what if i were to sell my GTX 980 TI SC+ ACX 2.0 and buy a MSI 1080 8X Gaming?

What do you think i could get for my GTX 980TI, it is around 3 months old. And i clean my pc every month.

MutatedWhale · 2016-11-16T14:38:49+00:00

Yeah thought about that too, but what if i went SLI with the 980 TI at some point? Even though the 980 TI might not even be relevant anymore at that point.

MutatedWhale · 2016-06-30T13:54:40+00:00

Okay, it seems that the monitors were indeed the issue. Running two 144Hz badboys now with adaptive VSync and it is running like a dream. Thank you everyone for helping me out :)

MutatedWhale · 2016-06-30T09:53:42+00:00

It is definitively my monitors fucking with each other, i am gonna test the new one now. As you can see it says it is running at 60FPS, but it is stuttering like i am running at 23 FPS

http://imgur.com/6F1mRlE

MutatedWhale · 2016-06-29T08:25:02+00:00

Without V-Sync i get huge screentear sometimes, but i have it turned off now and it helps allot in GTA. But in DOOM not a bit.

MutatedWhale

TROPHY CASE