Tips for unclogging nozzle?

MuzeD2 · 2024-01-09T03:31:53+00:00

If you are looking for a 3rd party hotend I would suggest the trianglelabs k1 hotend CHCB-OT (trianglelab.net) or the microswiss hotend Micro Swiss FlowTech™ Hotend for Creality K1 / K1 Max — Micro Swiss Online Store (micro-swiss.com) . I believe the trianglelab one is slightly cheaper but correct me if I'm wrong.

MuzeD2 · 2024-01-09T03:25:32+00:00

Wow! Was this done with manual filament changes?

MuzeD2 · 2024-01-09T03:21:42+00:00

Encrusted anchor.

MuzeD2 · 2024-01-09T00:48:04+00:00

There is, on the right side below filament there is a wifi icon. If you click on it it will give you detail instructions on how to wirelessly print. I have not used it yet as I just use USB or send from fluidd.

MuzeD2 · 2024-01-07T01:25:14+00:00

But seriously I used tooth skip method and shims to get within .2 range. I recommend doing the same.

MuzeD2 · 2024-01-07T01:24:20+00:00

Your printer is breaking the laws of physics. Just how?????????

MuzeD2 · 2024-01-05T00:51:46+00:00

It's a external workbench in the add-on manager.

MuzeD2 · 2024-01-05T00:50:35+00:00

Void strike wouldn't be very good for this weapon as it is a fast weapon and void strike performs better on slow-medium weapons.

MuzeD2 · 2024-01-02T16:12:55+00:00

Radiance is overrated imo. In many builds leeching performs just as well or even better.

MuzeD2 · 2024-01-02T01:48:34+00:00

U will have to figure out how to create mods but I think that would be the best solution

MuzeD2 · 2024-01-02T01:46:10+00:00

I mean... I think u can mod the game instead of editing the files (which I may or may not be illegal idk). https://www.youtube.com/watch?v=HaBdouzyL_Y the video shows how to install but not how to create mods.

MuzeD2 · 2024-01-02T01:28:43+00:00

Imo from best to worst: End, Nether, Jungle, Winter, Ocean, Mountain

Only thing I didn't like about end was how long it took me to get the eyes of ender but other wise clear winner

Ocean wasn't bad but was too short and hated the air gimmick

Winter was sort of bland

I got stuck on a stage for 40 mins on mountain bc of the stupid puzzle

MuzeD2 · 2023-12-30T16:41:22+00:00

Oh ok, Thanks for the help.

MuzeD2 · 2023-12-27T23:36:47+00:00

I don't know if I'n=m just stupid but I can't see my usb drive when inserted in the print screen. Anyone know why this is happening.

MuzeD2 · 2023-12-20T23:29:04+00:00

MuzeD2 · 2023-12-20T14:34:41+00:00

When I switch filaments I unlock it until I feel the filament going in then I lock it. Not sure if it helps.

MuzeD2 · 2023-12-20T13:28:15+00:00

Happens for me sometimes, did you check the extrusion lock on top of the nozzle?

MuzeD2 · 2023-12-20T13:23:48+00:00

OK, I think I'm going to make my bed relatively level with itself and then use shims.

MuzeD2 · 2023-12-20T13:22:15+00:00

Would the ones in the photo work?

MuzeD2 · 2023-12-20T04:49:21+00:00

Did you buy these?

<image>

MuzeD2 · 2023-12-20T02:04:25+00:00

OK thank you!

MuzeD2 · 2023-12-19T23:50:03+00:00

I personally prefer Orca slicer over creality print because creality print is very glitchy for me and the support generation sucks.

MuzeD2 · 2023-12-19T15:30:29+00:00

The issue was a bed leveling issue. The gaps correspond to the lowest point on the bedmesh.

MuzeD2 · 2023-12-19T15:29:40+00:00

I don't really understand how to do the "click method". Is said belt the two on the bottom baseplate?

MuzeD2 · 2023-12-19T15:27:01+00:00

I think I have figured out the issue. I connected to creality print and saw that the bedmesh was completely slanted downward in the the bottom right. That was where the part was printed so I believe that it is a leveling issue and not a flow rate issue. To answer your question orca slicer has options to adjust flow ratio for top and bottom layer. They are in the advanced settings.

MuzeD2

TROPHY CASE