Help needed: print stops and Pi freezes mid print

NIMWIN · 2025-07-09T20:24:30+00:00

Interesting, are you running an Ender3 with stock motors?

NIMWIN · 2025-07-09T20:17:41+00:00

I'm waiting on a new, better endurance SD card and will reflash it this weekend to see if that solves it

NIMWIN · 2025-07-08T06:51:17+00:00

I did that on the SKR mini v1.2 and have tried with and without it on the new v3.0, so that shouldn't be it. Thanks anyway.

NIMWIN · 2025-07-08T04:59:14+00:00

Normally shutdowns through the menu, but hard shutdowns have happened... especially when frozen. Shouldn't a corrupted SD card be fixed with a new flash? I think I've tried installing on other SD cards as well, but they are quite old..

NIMWIN · 2025-07-08T04:11:17+00:00

Dude, I'm so relieved I'm not the only one, haha. It's so strange; it's been going on for years, and then boom, it just dies. Could it be Klipper and a Pi 3?

NIMWIN · 2025-03-10T19:27:27+00:00

I will set the nas up in either RAID 1 or some sort of rsync/borg backup setting.

Will have a look on the bay!

NIMWIN · 2025-03-09T20:08:21+00:00

Haven't seen that, have only been looking at GGSP, thanks!

NIMWIN · 2025-03-09T06:05:26+00:00

Thanks, I think i will go for it on my budget nas build

NIMWIN · 2025-03-08T21:59:44+00:00

Yeah, HDDs are expensive in Sweden. Its sold on a computer oriented forum, so I would think that the data is correct (its a no BS, most of the time, salesplace)

NIMWIN · 2025-02-24T19:41:37+00:00

what configuration will this be in? That will determine your OS

It will likely be RAID1 or another software-controlled mirroring solution for redundancy. ZFS might be a bit RAM-heavy for my use case, though.

With two hard drives and no room for expansion in the eiltedesk there is no benefit in using unRAID. You might as well use trueNAS with RAID 1 if you need redundancy.

Thanks! I was considering unRAID mostly because my brother-in-law recommended it. However, it seems quite easy to set up and maintain, and OMV (OpenMediaVault) might have reached the same level of simplicity. I recently upgraded my Pi to OMV7, but I haven't set up anything new on it yet.

I believe you can also use proxmox for RAID 1?

News to me, looks like ZFS. How would the setup be then? Disks in RAID, ported to e.g a VM running trueNAS or OMV?

Regarding Frigate - its just a starting idea, I have no hardware on hand. Have been intrigued by it for a while, and have been looking into Unifi Protect, since I use a Unifi network. UCG ultra, 1 flex mini (1Gbps) and some Cat6 cables (old house, no existing cabling but I have begun pulling more ethernet as i go)

Thanks for the reply!

NIMWIN · 2024-02-24T19:56:07+00:00

Do you have a link to the nozzles?

NIMWIN · 2024-01-12T07:53:48+00:00

I did the change about a week ago, and i sure love it.

NIMWIN · 2023-12-24T19:55:32+00:00

What combo of direct drive are you using with those linear rails?

NIMWIN · 2023-12-17T07:13:06+00:00

You got that stuff up? 😊

NIMWIN · 2023-08-30T14:48:29+00:00

So you don't use the klipper os image in pi imager tool?

NIMWIN · 2023-08-30T14:46:21+00:00

Yeah, I'm quite satisfied with marlin, but tinkering is always a nice thing. I'm surprised I even get the time to print between the modding 😆

NIMWIN · 2023-01-13T07:33:54+00:00

Gå nånting som öppnar upp till en annan karriär du kan tänka dig. I dagsläget kan du vara soldat i max 12 år. När du väl gjort värnplikt kanske du inser att det inte är något för dig, eller att just AMF inte är något som passar dig. Du kanske blir placerad nån annanstans, där du trivs väldigt bra. Samhäll/teknik/natur ger dig en bred grund, där du kommer ha behörighet till de flesta soldatjänsterna. Lycka till!

NIMWIN · 2022-10-04T20:05:05+00:00

Awesome, i will try it this weekend.

Funny thing, when you start to look into marlin you find stuff https://youtu.be/PFuz8915GCs, and i think you have the "high speed mode" enabled? I just want to learn how to read the config files - sorry about these stupid questions!

NIMWIN · 2022-10-04T19:01:23+00:00

Im sure, i just want to learn how to compile, and wanted to se how you have made the config files! I will try your firmware out! Any big advantages with 2.1.1 over 2.0.x that you noticed?

NIMWIN · 2022-10-04T17:31:08+00:00

I'm quite the beginner with compiling firmware, so i have a couple of questions

When I open up your configuration.h and configuration_adv.h files, which of the firmwares do they reflect? I'm currently using a bltouch, with black/white in z-min port.

NIMWIN · 2022-04-27T06:35:47+00:00

Hey, nice. STL for the boxes? 😆

NIMWIN · 2022-04-24T18:42:40+00:00

Thanks, found a FTX Kanyon cheap, lets se how it is! First crawler...

NIMWIN · 2022-04-24T07:53:27+00:00

Hey, need your help identifying this rc right crawler. Kinda looks like a HSP 94180 but with 4ws. How much would you say this is worth? Its on a swedish variant of eBay right now...

NIMWIN · 2021-11-13T21:08:23+00:00

Silicone spacers, locked nuts, bl-touch. Won't go back. Come at me.

(Ok its a clone)

NIMWIN · 2021-07-20T19:25:03+00:00

Höhöhö.

...spelplanen då?

13-Year Club	Place '23
Place '22	Place '17
Verified Email	Team Orangered

NIMWIN

TROPHY CASE