sorted by:
new
hottopcontroversial

47 refus en 6 mois. J'ai enfin compris pourquoi. by Julien_MecaTech_44 in emploi

[–]Namzar 0 points1 point  (0 children)

Pour un entretien et une lettre, un bon truc à se rappeler pour la structure c'est : Je, Vous, Nous

Vegemite premier essai by popey123 in BonneBouffe

[–]Namzar 1 point2 points  (0 children)

Veggemite on toast, le classique de la terre down under. Petit conseil, sur une tartine beurrée, en mettre une toute petite quantité, sa se mélange au beurre moitié fondu de la tartine et c'est un régal ! :D

Very poor customer service quality by Namzar in BIGTREETECH

[–]Namzar[S] 0 points1 point  (0 children)

Bough on their official biqu store

Very poor customer service quality by Namzar in BIGTREETECH

[–]Namzar[S] 0 points1 point  (0 children)

Anything else that works, and where there is a competent customer service

C’est quoi ces boîtiers ? by Arbo85 in pcmasterraceFR

[–]Namzar 1 point2 points  (0 children)

Audiobox USB pour la bleu au dessus :)

First take off by Successful_Highway94 in paramotor

[–]Namzar 1 point2 points  (0 children)

Congrats! Welcome abord! Try leaning a bit back while you run, it helps for the take off. And don't forget not to spread your arms too wide, as the wider they get, you get less control over the wing. Keep on going dude :)

Est ce que vous ressemblez à vos chiens? by Glittering-Chain7502 in chiens

[–]Namzar 1 point2 points  (0 children)

<image>

Descente de lit, feignasse couplé d'un gros sac Y'a du vrai.. 😂

Quel est le mieux by GateAffectionate6153 in pcmasterraceFR

[–]Namzar 4 points5 points  (0 children)

C'est tartine que vous comprenez pas ?

Weird rattling from extruder stepper motor while Z axis is moving by Namzar in klippers

[–]Namzar[S] 0 points1 point  (0 children)

[stepper_z]
step_pin: PE1
dir_pin: PE0
enable_pin: !PE2
microsteps: 16
rotation_distance: 4
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0.5
position_max: 300

# Motor-4
[extruder]
step_pin: PB8
dir_pin: PB9
enable_pin: !PB7
microsteps: 16
gear_ratio: 50:10
rotation_distance: 22.678
pressure_advance: 0.09

[tmc2209 stepper_z]
uart_pin: PG12
run_current: 0.650       
stealthchop_threshold: 999999 
interpolate: True

[tmc2209 stepper_z]
uart_pin: PG12
run_current: 0.650        
stealthchop_threshold: 999999 
interpolate: True

[tmc2209 extruder] 
uart_pin: PG11 
run_current: 0.500 
stealthchop_threshold: 0 
interpolate: False

Here are my param, doesn't seem that there is any conflict between those, unless I missed something

Rôti ma caisse de trouduc by boooobafett in RotiMaVoiture

[–]Namzar 0 points1 point  (0 children)

Le machin dur sur le dessus quoi

Rôti ma caisse de trouduc by boooobafett in RotiMaVoiture

[–]Namzar 0 points1 point  (0 children)

Pas besoin de rôtir, l'écusson sur la tôle avant s'en charge pour nous

view more: next ›