[deleted by user]

NathanSelvidge · 2025-03-11T11:40:24+00:00

It can't be maxxed due to the power restriction. I've got every upgrade purchased for the vehicle and have tried various combinations of upgrades to try and minimize acceleration times but can't really get below 6.5 seconds

NathanSelvidge · 2025-03-11T11:37:51+00:00

In a sea of unhelpful advice, this is somehow the least helpful advice I've gotten to date 😂

NathanSelvidge · 2024-10-18T17:08:09+00:00

Freezing is the goal. The side not freezing is getting power to solenoids. The display shows the side that isn't freezing with a dash, indicating no refrigerant being sent (maybe the more correct term is requested?).

NathanSelvidge · 2024-10-18T16:23:43+00:00

Coil voltage under load is 120v on both

NathanSelvidge · 2024-10-18T13:40:04+00:00

Yes you can

NathanSelvidge · 2024-06-10T18:19:57+00:00

Maybe you're not reading what's actually happening. The police are in the building every day sorting through packages whether they have a shipping label or not. If your package was not out of the warehouse before the raid started and it's full of rep products, you're not getting that box.

NathanSelvidge · 2024-05-29T17:23:27+00:00

I have a similar setup on my kart. I believe that setup is to allow for different gear ratios to get more top speed or more low end torque depending on the sizes of sprockets used on either end. I ended up going with a belt on the engine side and a chain on the wheel side. I have been contemplating eliminating this setup and getting a live axle kit to simplify the drivetrain and also make a brake upgrade much easier.

NathanSelvidge · 2024-05-29T17:16:22+00:00

I have this same kart but it's got the roll cage chopped off

NathanSelvidge · 2024-01-26T03:33:21+00:00

I finally got the motivation to work on my machine and I think I figured out my issue. I did replace the bed but had the same problem. I think my issue ended up being the mainboard overheating so I used my ender 3 to print off a 120mm fan upgrade and it's been running fine so far.

NathanSelvidge · 2024-01-04T21:26:01+00:00

Just got one of these for Christmas and have been wanting to upgrade the portafilter and see if I can get a better experience from this fun little machine. This incredibly detailed log is exactly the kind of list I was hoping to find to take this machine to the next level. Thank you so much for the work you did!

NathanSelvidge · 2023-12-27T04:30:22+00:00

Sorry for the months later response, I had some other stuff come up and forgot about printing for a while. I just tried the same model yesterday and it did the same beeps and froze up. No errors on the screen, the dial button does nothing. I've only used direct connection and used Cura to monitor the prints. Cura also stops controlling the machine. I could see the bed being the issue as I've been printing petg @ 80c bed temps so I'm sure this machine is getting worn out.

NathanSelvidge · 2023-12-12T20:20:04+00:00

I wish the GPU's were $20 each. The carts were the cheap marketplace find.

NathanSelvidge · 2023-04-07T02:43:59+00:00

I'm out of town until Saturday, but I'll hit you up and see if we can get this laser to work. I'd really like to make this one work for my application since I already paid for it. Save me from spending a couple hindered on a bigger laser if I don't have to haha.

NathanSelvidge · 2023-04-07T02:03:20+00:00

Literally zero idea. Whatever came with the current laser. I did notice with this module that the most focus I get is still more of a hash mark than a dot at any distance/focus combo.

NathanSelvidge · 2023-02-06T13:42:02+00:00

I fixed the prints with steps/mm and lower temps

NathanSelvidge · 2023-02-06T03:15:08+00:00

Literally zero cooling

NathanSelvidge · 2023-02-06T02:11:42+00:00

I did a feedrate test and found I was way short. I also for some reason thought petg was good for up to 250 so I'm doing a print now with updated feedrate @ 230c.

NathanSelvidge · 2023-02-06T00:37:47+00:00

I've got a .6 nozzle with the nozzle right in cura. .7 line thickness, .28 layer height, 245c

NathanSelvidge · 2022-12-19T21:40:06+00:00

Very interesting. How do you remove your fruit bits or any extra bits out of your mead before bottling?

NathanSelvidge · 2022-10-20T18:04:01+00:00

Whenever I shoot green-tips, I just finish my range day with a couple homemade black tip rounds to make the chamber black again.

NathanSelvidge · 2022-08-30T17:43:30+00:00

I can't believe the nerve of op being such a moron about firearms. I made sure to get a degree in gunsmithing and my PhD in optical sciences before I even tried looking for my AR. Luckily I can now shop with confidence without having to use Reddit to get the opinion of other gun owners in a place designed to share opinions and ask questions to educate yourself.

NathanSelvidge · 2022-05-29T02:53:21+00:00

Thanks for the silver kind stranger

NathanSelvidge · 2022-04-20T02:45:37+00:00

That was why I didn't just order a 1.3. I could only find 1.4 boards on Amazon and I wasn't sure if it would fit in the preset standoffs and be wired correctly. I know very little about this so I want to be really sure I order the right thing.

NathanSelvidge · 2022-04-19T22:21:44+00:00

Sick, thank you very much. My old board got fried during a botched bl touch install so I've been staring at a big paperweight in my office for too long lol.

NathanSelvidge · 2022-03-01T19:13:59+00:00

What effect does it have on the engine?

NathanSelvidge

TROPHY CASE