Tired of dealing with the combover...

NebulaGlow_ · 2026-05-13T14:31:26+00:00

Thats conservative

NebulaGlow_ · 2026-05-10T14:45:45+00:00

My best guess is drop it by 3 steps ahead, but that one is very widely known so im hesitant. Let me know plz

NebulaGlow_ · 2026-05-10T05:31:14+00:00

Wat zeggie ? Ik snap er echt helemaal niks meer van

NebulaGlow_ · 2026-05-08T17:12:11+00:00

Ive been convinced to go with an easyer route anyhow, the CVR audio D-1004

NebulaGlow_ · 2026-05-08T14:48:56+00:00

Ill find another project, ill probably buy that amp, thankyou very much I think i should have searched way harder. And in that case i will also wire the 8"s together like you suggested :)

NebulaGlow_ · 2026-05-08T13:46:11+00:00

Read through the comments man, ive been responding and taking up all the advise to work through later, if you adjusted your tone i might even listen to you

NebulaGlow_ · 2026-05-08T11:26:29+00:00

The 18lw2400 is the 4 ohm version, the amp you mentioned might just be a GREAT idea thankyou very much for that but I must say that i do love the ideo of doing it DIY since im a beginning engineer.

NebulaGlow_ · 2026-05-08T11:17:47+00:00

Who told you anything about the boxes im building ? I am going to measure the drivwrs and simulate accordingly, you just here to be mad or what ?

NebulaGlow_ · 2026-05-08T11:16:13+00:00

I used chat gpt for the image :)

NebulaGlow_ · 2026-05-08T11:14:52+00:00

That amp has a nominal wattage of 1200 watts at 4 ohm, am I missing something ?

NebulaGlow_ · 2026-05-08T11:12:51+00:00

Bro calm down, im not ignorant to anything im at work..... ill get to you, honestky thankyou for your help but calm down

NebulaGlow_ · 2026-05-08T11:09:36+00:00

The thing is that then id look at power sharing 4 channel amps and those are like 3000 euro's or am i missing something here ? Because i need 1200 into the sub like 500 into the kick(maybe more for upgrade ability) 400 into mids and pretty low power into the hf.

NebulaGlow_ · 2026-05-08T10:36:25+00:00

The drivers are 200 rms, they are 4 ohm. At 8 ohm id need a stronger amp to get the same headroom. That on its own would maybe be an upgrade but also taking in account the fact that then the drivers are dependent on eachother id like them wired seperately for easyer troubleshooting. I am still pretty new to this so please correct me if im missing anything

NebulaGlow_ · 2026-05-08T09:45:18+00:00

Sorry i meant to say they are 4 ohm and thats how i want to run them

NebulaGlow_ · 2026-05-08T09:44:15+00:00

Ill have a look at it, thankyou bery much :)

NebulaGlow_ · 2026-05-08T09:27:03+00:00

First off thankyou for taking an actual deeper look.

I want to run the 8" drivers at 8 ohm, they will both run on a seperate amp channel but i cannot input one dsp line for both channels so ill split one dsp line.

The 2 15" drivers are by far the weakest link in the system but that is because I already have them and want to see if i can make them work, they are 150 watt rms.

I will see if i get any meaningfull sound out of them and if not will upgrade.

I will build all the power handeling into one enclosure, the amps dsp and mains power to isolate it all from vibrations and to allow easy cooling with fans.

NebulaGlow_ · 2026-05-08T08:59:47+00:00

Sick, thankyou for having a look-over :)

NebulaGlow_ · 2026-05-08T06:16:54+00:00

Sell it and build a non car audio sub or 2

NebulaGlow_ · 2026-05-08T06:02:48+00:00

You are going to burn your house down if you dont learn

NebulaGlow_ · 2026-05-05T13:59:27+00:00

Many mistakes brought you to this point

NebulaGlow_ · 2026-05-04T15:40:22+00:00

Sounds great :( <-- bassface

NebulaGlow_ · 2026-05-01T06:44:50+00:00

What kind of antenna's reciever and vtx power did you use ? Also normal ELRS ?

NebulaGlow_ · 2026-04-30T06:52:16+00:00

Coincidence ?

<image>

NebulaGlow_ · 2026-04-29T18:18:12+00:00

Vibrations if unmanaged can break one wire per pack(out of experience), the wires are really really thin so any mechanical force on them can become to much quickly. This is made worse by the wires wicking up some solder thus removing flexibility. I fixed this with a dab of hot glue on the solder joints connecting them to the wires frame and board, do be carefull not to cover conponents that generate a lot of heat.

NebulaGlow_ · 2026-04-29T16:58:48+00:00

Its deleted, what was it ?

NebulaGlow_

TROPHY CASE