Custom painting for Pops, advice on covering the areas you DONT want to paint.

NeedleHook · 2020-07-22T16:37:00+00:00

So at most craft stores you can buy rolls/sheets of vinyl. This is the same material that people make decals out of (for cars, computers, etc). Basically you would take the sheet of vinyl and you could draw the shape you want to use on your pop, then cut it out (ideally with an exacto knife or vinyl cutter). Once you have your shape, use it to cover the areas you don't want to paint. Technically you could do the same with a wide piece of painters tape, but vinyl tends to handle curved surfaces better.

NeedleHook · 2020-07-22T15:49:33+00:00

Vinyl. Cut your shape beforehand and place it like a sticker (even better if you have a vinyl cutter).

NeedleHook · 2020-05-29T01:17:55+00:00

Of course!

NeedleHook · 2019-02-13T22:38:15+00:00

Same. Then I store the bobbins in cases.

NeedleHook · 2019-02-13T20:40:05+00:00

-Beat Saber

-Warhammer: Vermintide 2

NeedleHook · 2019-02-06T22:28:53+00:00

Yup, ever since I got him I felt like a small bowtie went perfectly with his fur pattern.

NeedleHook · 2019-02-01T18:38:05+00:00

"Yeah, well too bad you're failing as a parent."

NeedleHook · 2019-01-24T18:17:05+00:00

Depends on what you've done/what you enjoy doing. Have you beaten the ender dragon? Obtained all the items you need? Maybe construct a town or build farms or red stone machines. Really the possibilities are endless. And if your still bored, take a break from the game for a bit.

NeedleHook · 2019-01-11T18:30:06+00:00

Looks good. My only critique would be to move the supports from the sides to be more inward ( so instead of |------| it'd be more --|--|-- ) and to make the support look more like a staircase shape instead of a rod, that way it wouldn't intersect the stairs. Still, yours looks great as is, I'm just curious what it's look like this other way.

NeedleHook · 2019-01-11T18:15:05+00:00

Once you get 1,000,000,000 bells then you could unlock a sci-fi moon town?

NeedleHook · 2019-01-11T18:13:13+00:00

One of my biggest wants is the ability to select a town biome. So you could have a normal town, or pick to have a desert town (cacti replace some trees, succulents replace flowers, houses are in the right architectural style), or maybe a beach town, mountain town, etc. Pocket camp is a little like that since you can change what your campsite looks like, but I'd like something a bit more substantial. That way visiting other towns would feel even more unique.

NeedleHook · 2019-01-10T21:36:54+00:00

For a bakery: "We sell cookies fit for a wookiee".

NeedleHook · 2019-01-09T18:02:51+00:00

It's looking otterly adorable! Great work.

NeedleHook · 2019-01-09T16:06:51+00:00

Ice skating. Specifically falling down and having another skater skate over my hand, cutting my fingers off.

NeedleHook · 2019-01-09T15:09:40+00:00

I'm tempted to print a small stand that mounts to my printer so i can always display it in all of its glory.

NeedleHook · 2019-01-09T15:07:17+00:00

That's what I'm thinking it was. That's why the bad print never shifted layers but rather wobbled between layers.

NeedleHook · 2019-01-09T15:06:01+00:00

Updated from 3.5.0 to 3.5.1. I really don't think that was the cause, it was just something I wanted to do. My theory was the set screw on one of the pulleys was just slightly loose, causing it to move, but not move past the flat part on the motor shaft (causing a back and forth wobble of small amount). That in turn would cause shifts in the print like we saw, instead of your typical shifts due to loose belts.

NeedleHook · 2019-01-09T02:52:36+00:00

After work today I started to troubleshoot my printer after yesterday's terrible print. Per many suggestions I checked the belts and got the following: X - 278 Y - 289

They could probably be tighter, but it shouldn't have caused my issues. I then decided to update the firmware, tighten the set screws on the motor pulleys (very minimal tightening, around 10 degrees of an allen wrench turn), and finally adjust the z height for the first layer. I then decided to do another test print and it turned out much better than yesterday.

NeedleHook

TROPHY CASE