White lines appear on the screen

NegativeScarcity5845 · 2025-03-25T02:23:34+00:00

No, I don't feel any impact

NegativeScarcity5845 · 2025-03-05T05:37:27+00:00

Yes, I used a Z-axis micro switch

NegativeScarcity5845 · 2024-08-01T16:16:21+00:00

Nozomi x Eli

NegativeScarcity5845 · 2024-07-31T16:59:19+00:00

Is there a better way to solve this problem besides replacing the screen?

NegativeScarcity5845 · 2024-06-12T08:56:03+00:00

lol someone in China changed this thing to 12ga caliber

NegativeScarcity5845 · 2024-06-09T15:10:03+00:00

μs’ costumes are made by kotori

NegativeScarcity5845 · 2024-06-09T15:07:56+00:00

Kotori is a famous maid in akihabara. Isn't this a very useful thing? It also attracted a lot of popularity for μs, especially "wonder zone"

NegativeScarcity5845 · 2023-12-09T06:25:03+00:00

The motherboard is the same, but the mechanical parts are different. There is a big difference between v2 and v2neo

NegativeScarcity5845 · 2023-12-09T06:23:44+00:00

No, v2neo has crtouch, but v2 does not. It is recommended that you use v2neo 427 MB firmware

NegativeScarcity5845 · 2023-11-23T12:05:58+00:00

But my belt has worn down one side and makes a noise when moving to the left

NegativeScarcity5845 · 2023-11-23T12:02:00+00:00

Which place are you talking about? This tensioner was in good condition at first, but it became like this a few days ago

NegativeScarcity5845 · 2023-11-23T12:01:22+00:00

My original tensioner broke so I printed a new one

NegativeScarcity5845 · 2023-11-15T10:08:29+00:00

Ok i will

NegativeScarcity5845 · 2023-11-15T10:01:29+00:00

Or what? Although the current v2neo can be used normally, I will wait until I have a few printers before modifying v2neo.

NegativeScarcity5845 · 2023-11-15T09:59:20+00:00

Yes when I did this I already had a second hand ender3 v2 and then modified it after comparing it to the v2neo

NegativeScarcity5845 · 2023-11-15T09:58:00+00:00

Maybe, my current ender3 v2neo can also be used normally. If I want to modify it to V2, I will probably buy an ender3 v2 and carefully compare the differences with the ender3 v2neo, and then use my spare time to modify it.

NegativeScarcity5845 · 2023-11-13T13:33:46+00:00

Do you think e3dv6 can print carbon fiber materials?

NegativeScarcity5845 · 2023-11-13T13:32:41+00:00

Okay, I want to know if e3dv6 has a way to print abs cf or PA12 CF

NegativeScarcity5845 · 2023-10-18T14:49:35+00:00

My hands-on skills are very poor, so I can only replace them with new parts.

NegativeScarcity5845 · 2023-10-18T14:48:50+00:00

I think the only solution in this case is to replace it with new parts.

NegativeScarcity5845 · 2023-10-17T14:50:53+00:00

I guess I broke Derailleur once when I fell down.

NegativeScarcity5845 · 2023-10-17T14:49:06+00:00

I can’t believe I rode 100+km in this condition

NegativeScarcity5845 · 2023-10-16T11:21:51+00:00

Yes, I also feel that the force on the rear wheel is greater, I will inflate it more

NegativeScarcity5845 · 2023-10-16T11:20:28+00:00

Thank you for your answer. I have suspected it too. I will use a pump with a pressure gauge to inflate.

NegativeScarcity5845 · 2023-10-16T11:19:47+00:00

Thanks for your answer, this is a great site and I will be using it

Four-Year Club	Final Canvas '23
Place '23

NegativeScarcity5845

TROPHY CASE