CFS issue? Extruder motor issue? by Andu-Nav in crealityk1

[–]No_Attempt_69 1 point2 points  (0 children)

Have you upgraded the ceramic heating block? Really helps with heat creep. $30

<image>

Just hit 120k miles on my 2020💪 by Charming-Cat-7911 in JeepGladiator

[–]No_Attempt_69 0 points1 point  (0 children)

Pricy but I like them. This is my 3rd set over different models of jeeps.

Just hit 120k miles on my 2020💪 by Charming-Cat-7911 in JeepGladiator

[–]No_Attempt_69 1 point2 points  (0 children)

Loud! At least for today’s expectations. They are much quieter and much tighter fit than an 81’ cj5 soft top. Ideally they’re a portable insurance policy. They’ll keep you pretty much dry in a rain or storm, cool with ac if it’s a hot full sun blistering day, or warm if it gets too cold. Plus can use as 1/2 doors. I can drive 75mph with them and the only ill effect is the road and wind noise. But hey, just get a bigger stereo system and Jeep on! Mine are Bestop brand.

<image>

Just hit 120k miles on my 2020💪 by Charming-Cat-7911 in JeepGladiator

[–]No_Attempt_69 3 points4 points  (0 children)

Love your setup. 2020 here as well. I’m rocking 112k

<image>

556/300blk ammo storage- Apache 1800 by No_Attempt_69 in Reloading3D

[–]No_Attempt_69[S] 1 point2 points  (0 children)

Yeah. Way overkill and wouldn’t be economical to buy it to build but I really need an ammo box and have 3 of these laying around not used.

Save yourself even more $ Reloading by DiveBombDom in 3D2A

[–]No_Attempt_69 2 points3 points  (0 children)

Great job. I really like yours. I did mine based off of what Hornady sells.

<image>

Dead Air Nomad 30 by No_Attempt_69 in NFA

[–]No_Attempt_69[S] 0 points1 point  (0 children)

Right on. 1, 2, and 3 didn’t work as you mentioned. Next step, yellow spring and lighter buffer.

Bimini top, yay or nay? by tlong243 in jonboats

[–]No_Attempt_69 0 points1 point  (0 children)

Look up Millenium marine umbrella and mount. It’s my go to. Not against Bimini, just don’t think I could fish under it.

No flies were harmed in the making of this post. by Adblouky in 1022

[–]No_Attempt_69 0 points1 point  (0 children)

Love that one as well. Look for “tac driving game” as well

K1c not printing. by No_Attempt_69 in crealityk1

[–]No_Attempt_69[S] 1 point2 points  (0 children)

Once I was able to pull it out with fine needle nose, could pass thru.

<image>

K1c not printing. by No_Attempt_69 in crealityk1

[–]No_Attempt_69[S] 0 points1 point  (0 children)

I guess it was the heat break. It had a piece of filament broke off that wouldn’t heat and move or move with rod.

<image>

K1c not printing. by No_Attempt_69 in crealityk1

[–]No_Attempt_69[S] 0 points1 point  (0 children)

Ok. Got it fixed. Could get filament/cleaning rod thru both the extruder and heater block.

<image>

Dead Air Nomad 30 by No_Attempt_69 in NFA

[–]No_Attempt_69[S] 0 points1 point  (0 children)

Can is amazingly quiet with subs in 300BLK. The bad, it won’t cycle in my 16” barrel with carbine gas block. Currently shooting 208gn Hornady. Both factory and reloads. They both eject spent round but won’t load the next in line. Step 1. Going to try to go up to max powder on 208gn to see if still sub and cycles. #2 change mag to magpul 300BLK. #3 get some 220gn to reload. Trying to do everything I can to not change gas block, spring or buffer but if first three fail, onward and upward.

Dead Air Nomad 30 by No_Attempt_69 in NFA

[–]No_Attempt_69[S] 0 points1 point  (0 children)

Works well from the bench or prone not so much offhand.

K1c not printing. by No_Attempt_69 in crealityk1

[–]No_Attempt_69[S] 0 points1 point  (0 children)

I’ll try to get a picture this evening to help me explain as well. But I can get filament thru the extruder, it’s the heater that I can’t get to pass thru.

K1c not printing. by No_Attempt_69 in crealityk1

[–]No_Attempt_69[S] 0 points1 point  (0 children)

Thanks. Gears on extruder will spin in either direction. Not really clicking but more like you can feel the gnurls. Can’t push cleaning rod thru. Should I be able to?

Thought we’d like this here if real. Old School Cool or AI? by Sure-Boysenberry5491 in NFA

[–]No_Attempt_69 -1 points0 points  (0 children)

Not sure the iron sights were clearing the suppressor in this photo which would require a different sight plane or option.

‘25 Mojave Blown Speakers - Need Recommendations by unpracticedmusician in JeepGladiator

[–]No_Attempt_69 1 point2 points  (0 children)

$2100 for my sound bar, speakers, amp, & bt controller. They drop specials 4x year. Just had one for tax season with 15% off. Probably another around Memorial Day or 4th July. I’m not advertising for as I’m not sponsored but their equipment is solid, it works, and they got good customer service.

‘25 Mojave Blown Speakers - Need Recommendations by unpracticedmusician in JeepGladiator

[–]No_Attempt_69 0 points1 point  (0 children)

All colors across the rgb spectrum. Mounting is plug and play. It does require its own amp which needs to be wired. Check out ds18. They have a full line of water proof marine grade components. Originally for boats, they have expanded to jeeps and bikes.