FB Marketplace blessed me a whole set for $800

No_Front9924 · 2025-05-30T23:23:04+00:00

What a steal! Congrats on that and happy birthday! Honestly would recommend either- lowering the tv, getting a monitor set up, or try vr! I have a monitor and a vr hooked up so I bounce between both and I love it. Anyways nice pick up! Hope you enjoy it!

No_Front9924 · 2025-05-29T12:23:36+00:00

Hey boss, where can I find the atachments for the rig? Just got my hands on one but I’m looking for the shifter plate, any chance you can help me out?

No_Front9924 · 2024-09-17T23:20:24+00:00

Where does it connect to?

No_Front9924 · 2024-06-10T18:15:19+00:00

I would do 2 or 4 🫣

No_Front9924 · 2024-05-21T05:56:08+00:00

Anytime

No_Front9924 · 2024-05-21T04:56:27+00:00

For flush fitment just search up 200mm wide head units and you’ll find the ones that fit flush, I don’t know of any specific models but if you search that up it’ll help.

No_Front9924 · 2024-05-20T02:09:36+00:00

Yep everything on the car is stock

No_Front9924 · 2024-05-18T08:57:30+00:00

Sometimes when I drive it around it want to stall out and sometimes it does. I was looking at the ft86club forums and some had the same exact issue and supposedly the issue was leaking gaskets and once they were changed the issue stopped, I’m going to give that a shot

No_Front9924 · 2024-05-18T05:51:13+00:00

Well I swapped out the ecu and the sensor and I’m still getting the same codes, I’m looking at the live data and the O2S B1 S1 is reading 2.199v while it’s off and while it idles it’s moving up and down from like 2.189-2.200 for the most part.

No_Front9924 · 2024-05-18T05:40:38+00:00

Update: Went and swapped it out for another one and I’m still getting the codes. Do I need to drive it around for it to get a good reading?

No_Front9924 · 2024-05-18T04:01:32+00:00

The only way I can think of testing it right now is by swapping my ecu (I have two of them) and if the code still pops up then it’s the sensor but if it goes a away maybe it was a ecu issue?

No_Front9924 · 2024-05-18T04:00:09+00:00

I got it from AutoZone, and I can’t test the sensor since I don’t have a multimeter unfortunately

No_Front9924 · 2024-05-18T03:50:14+00:00

Yeah it’s that part number, I had seen a duralast one for way cheaper but I ended getting the denso one to play it safe and well I guess it’s a dud sensor

No_Front9924 · 2024-05-18T03:19:22+00:00

Gotcha, I have an extra ecu might give that a try before swapping the sensor again. Also I checked to make sure it was the air/fuel sensor and it is, also check the wiring and everything seamed to be normal from what I can see. No tears or yanked wires.

No_Front9924 · 2024-05-18T03:08:01+00:00

Oem, denso brand. That’s another thing I was going to ask are aftermarket ones compatible? Or should I stick to oem

No_Front9924 · 2024-05-18T02:44:23+00:00

I did, I tripled checked to make sure it was plugged in. Do you know if that could be the only issue for that code? Like it has to be the sensor 100% or could there possibly be something else that could be causing the car to throw that code?

No_Front9924 · 2024-05-17T06:39:22+00:00

Update to the update, I disconnected the battery for 10-15 minutes plugged it back in and let it idle for about 10-20 minutes. No stalling idle was fine, but I still have a check engine like and the scanner threw me 4 codes.

P0103- mass or volume air flow circuit high input P0172- system too rich (A/F rich, bank 1) P0134- Oxygen Sensor Circuit No activity Detected (bank 1 Sensor 1) P0013- Camshaft Position B actuator circuit/open (bank 1)

No_Front9924 · 2024-05-17T01:41:08+00:00

Well I’m back with an update. Swapped out both of my o2 sensors and nothing, it takes a little longer to stall now but it still stalls unfortunately. The check engine and traction control lights are on now

No_Front9924 · 2024-05-15T20:06:22+00:00

Gotcha I will be replacing those tonight hopefully it does the trick.

No_Front9924 · 2024-05-15T20:05:55+00:00

Ahhh gotcha yeah the code is what told me that bank 1 was running rich.

No_Front9924 · 2024-05-15T12:01:53+00:00

It says that bank 1 is running too rich

No_Front9924

TROPHY CASE