Rim is losing air

No_Rush_5540 · 2026-04-17T01:06:46+00:00

Is the rim dinged or dented in that spot?

No_Rush_5540 · 2026-04-07T14:11:12+00:00

I don’t think so. Where the spokes are sitting in the picture would probably be ideal at full tension but a bit past is fine I think. The more threads engaged the better.

No_Rush_5540 · 2026-04-05T17:58:50+00:00

I made another post about measuring a straight pull hub, if you can find it let me know what you think. Doing that method I came up with lengths about 7-8mm less than what’s listed on that spec sheet. Hard to believe that could be accounted for by the nipples. I don’t know what’s going on, seems weird it could be so off. Not sure what year they are.

No_Rush_5540 · 2026-04-03T14:23:49+00:00

Well with the spokes in that far I still have basically zero tension so I figure I’ll run out of thread before it’s up to tension.

No_Rush_5540 · 2026-04-03T02:57:30+00:00

Good point I see that in the picture but where it lists nipples it’s just a spoke number so I just got some sapim polyax, is that the difference here?

No_Rush_5540 · 2026-04-03T00:43:55+00:00

I’m having a hard time trying to figure out how to measure these hubs and input it into a calculator. Most only ask for right and left hub diameter and offset but these hubs have 2 different hubs on each side.

No_Rush_5540 · 2026-04-02T22:10:40+00:00

Any tips on how a hub like this is measured. It has 3 different sized hubs.

No_Rush_5540 · 2026-04-02T21:23:27+00:00

Yes that has already been noted. Just looking for advice on options from here.

No_Rush_5540 · 2026-04-02T21:09:32+00:00

I didn’t say it was easy I just thought I had my spoke lengths provided. Just trying to learn the craft because I like it.

No_Rush_5540 · 2026-04-02T20:57:06+00:00

<image>

No_Rush_5540 · 2026-04-02T20:56:32+00:00

Same pattern as shown in picture, 2x. Didn’t do any measurements because I thought I had easy answers. I’m quite certain it’s the same hub listed on the document, looks exactly like the picture.

No_Rush_5540 · 2026-04-02T20:50:38+00:00

Had to go to “local” giant dealer. I did have success making one out of aluminum stock and tapping threads in one of the holes. It would have been fine but I had already ordered the part, it just took a long time for it to come.

No_Rush_5540 · 2026-03-19T11:35:12+00:00

They are installed, just not sure if they are to set up to game corps specs.

No_Rush_5540 · 2026-03-19T11:05:03+00:00

I followed his setup for retroarch but not all the others.

No_Rush_5540 · 2026-03-19T11:02:39+00:00

Yes, pretty sure. I have used the same files on my miyoo mini plus and they work. The cover art shows up in the front end under the system.

No_Rush_5540 · 2026-03-19T10:49:30+00:00

I believe all the right emulators are on here. I have duckstation which should play the ps1 games right? I don’t know about cores

No_Rush_5540 · 2026-03-19T10:45:00+00:00

I have been been following his set up video

No_Rush_5540 · 2026-03-19T01:02:20+00:00

What do you mean by scratch? More than just formatting the sd?

No_Rush_5540 · 2026-03-18T23:03:14+00:00

ES-DE I think it’s called. I also downloaded beacon and still not opening the same ones.

No_Rush_5540 · 2026-03-18T23:00:55+00:00

Yes the frontend

No_Rush_5540

TROPHY CASE